manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Instruction Manual

The Schweitzer Engineering SEL-2032 Instruction Manual is a comprehensive guide designed to assist users in operating this cutting-edge product efficiently. With step-by-step instructions and detailed explanations, this manual is available for free download on our website. Unlock the full potential of your SEL-2032 today at manualshive.com.

Share
Download
background image

2.4

SEL-2032

 

Communications Processor

Instruction Manual

Date Code 20120126

Installation

Mounting and Connections

Power
Connections

The terminals labeled “POWER” on the rear panel must be connected to a 
power source that matches the power supply (POW SUP) characteristics 
specified on the rear-panel nameplate of your SEL-2032. If you provide a dc 
power source, you must connect the source with the proper polarity as 
indicated by the “+” and “

” labels on the power connector. The SEL-2032 

internal power supply has very low power consumption and a wide voltage 
tolerance. See 

Specifications on page 1.28

 for complete power supply 

specifications.

Alarm Contact 
Connection

The SEL-2032 includes an alarm output contact connected to pins 1 and 3 on 
the rear panel. At the factory, the alarm contact is configured to be closed for 
an alarm condition, and open for normal operation. This is a Form B contact 
because it is closed when there is no power. To invert the alarm output to close 
under normal conditions, change soldered jumper, JMP3, on the main board to 
select Form A contact usage. See 

Table 2.1

 and 

Figure 2.4

 for jumper settings.

The alarm contact asserts when no power is connected to the SEL-2032, the 
power supply fails, or self-test diagnostics detect a failure. Self-test diagnostic 
failures include memory failures, power supply failures, and invalid setting 
failures. See 

STATUS on page 8.21

 for a discussion on these failures. With the 

default ALARM setting (Global Settings), the alarm contact is pulsed when 
Level 2 communication is accessed, or when an SEL-2032 setting change is 
accepted.

The ALARM LED illuminates whenever the alarm contact asserts.

IRIG-B 
Input Connection

The SEL-2032 accepts a modulated or demodulated IRIG-B signal through a 
rear-panel BNC connector labeled “MODULATED/DEMODULATED 
IRIG-B IN.” An internal setting selects between modulated and demodulated 
IRIG-B (Global Settings). The factory-default setting is demodulated IRIG-B 
time input.

The SEL-2032 can also accept IRIG-B on the IRIG-B pins of Port 15. By 
default, the IRIG on Port 15 is configured as an output, but it can also be used 
as a demodulated IRIG-B input. To do this, set JMP1 and JMP2 in the 2-3 
position. Also, the IRIG setting must be set to demodulated. See 

Table 2.1

 and 

Figure 2.4

 for the main-board jumper positions for setting-up the Port 15 

IRIG-B.

Use a modulated IRIG-B signal for the input to the SEL-2032 if it is available. 
The modulated signal is isolated by a transformer. The demodulator in the 
SEL-2032 includes automatic gain control. You can use a demodulated signal, 
but it may not be adequate if the cable to the source is too long.

An internal element asserts in the SEL-2032 Global database region when an 
adequate IRIG-B input signal is received. If no external IRIG-B input signal is 
applied, the SEL-2032 generates an IRIG-B signal. The SEL-2032 includes an 
internal battery-backed clock/calendar that maintains correct time with or 
without external power.

IRIG-B Output 
Connection

The SEL-2032 distributes a demodulated IRIG-B output signal through all of 
its 16 rear ports. You can use this feature to synchronize any type of device, 
such as a relay, fault recorder, or meter that can decode the IRIG-B signal; you 
need only to connect the device to the desired SEL-2032 rear serial 
communication port using a special cable designed for both communication 
and IRIG-B signal. The IRIG-B signal is on pins 4 and 6 of the 9-pin, 
subminiature “D” connector (see 

Figure 2.1

 and 

Table 2.3

).

Courtesy of NationalSwitchgear.com

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

Ubiquiti PowerBeam AC Gen2 Quick Start Manual preview
PowerBeam AC Gen2
Brand: Ubiquiti Pages: 22
Gate NanoAAB User Manual preview
NanoAAB
Brand: Gate Pages: 8
AXIOMTEK eBOX532-100-FL Series Quick Installation Manual preview
eBOX532-100-FL Series
Brand: AXIOMTEK Pages: 2
TDK InvenSense RoboKit1 Hardware Reference Manual preview
InvenSense RoboKit1
Brand: TDK Pages: 13
Patton electronics FORESIGHT 6300 User Manual preview
FORESIGHT 6300
Brand: Patton electronics Pages: 145
Gundermann VIDEOWALL LEDWALL Optimizer HQ P2 Manual preview
LEDWALL Optimizer HQ P2
Brand: Gundermann VIDEOWALL Pages: 12
Congatec COM Express conga-TC87 User Manual preview
COM Express conga-TC87
Brand: Congatec Pages: 114
netsys NVF-2400S User Manual preview
NVF-2400S
Brand: netsys Pages: 164
Spirent A2-400 Installation Instructions Manual preview
A2-400
Brand: Spirent Pages: 22
Broadband Products Xtreme Networked Boat User Manual preview
Xtreme Networked Boat
Brand: Broadband Products Pages: 16
Alcatel-Lucent Broadband 700 MHz Brochure preview
Broadband 700 MHz
Brand: Alcatel-Lucent Pages: 8
FDI USB-ICP-SAB9 Quick Start Manual preview
USB-ICP-SAB9
Brand: FDI Pages: 15
Datavideo NVW-150 Instruction Manual preview
NVW-150
Brand: Datavideo Pages: 71
Tektronix 7B87 Instruction Manual preview
7B87
Brand: Tektronix Pages: 143
WEIGL Nanotec Instruction Manual preview
Nanotec
Brand: WEIGL Pages: 6
A.E.B. 628450000 Assembly & Instruction Manual preview
628450000
Brand: A.E.B. Pages: 10
Enterasys 1G58x-09 Configuration Manual preview
1G58x-09
Brand: Enterasys Pages: 808
ABB M1M 10 Quick Start Manual preview
M1M 10
Brand: ABB Pages: 2

Brands by name

Popular brands

Load more brands