Schweitzer Engineering SEL-2032 Instruction Manual Download Page 237 | Manualshive

Page: 237 / 354

background image

8.21

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Serial Port Communications and Commands

Command Set

You cannot enter or modify settings with this command. Change settings with
the

SET

command.

STATUS

Use the

STATUS

command (Access Level 1) to inspect self-test status, the

configuration of this unit, and the status of each port. The SEL-2032
automatically sends the

STATUS

command response message to Port F

whenever the self-test software enters a warning or failure state. Add a repeat
count parameter to cause the

STATUS

command to repeat a given number of

times. For example, type

STATUS 4

to view the status information four times.

The SEL-2032

STATUS

report format appears as shown in

and

.

*>>

STATUS <Enter>

COMMUNICATIONS PROCESSOR - S/N XXXXXXXX Date: 2/16/04 Time: 00:01:17
FID



SEL-2032-R103-V0-Z001000-D20050418 FID



SLBT-2030-R103-V0-Z000000-D20010122

SELF-TESTS

RAM SRAM CODE ARCH EEPROM P.S. SET BATTERY SETM
512 kb 1024 kb OK 1792 kb OK OK OK OK OK

IRIG-B Input: Absent
I/O Board: Installed

Port  Status   Success Rate SET M Data
1 Active(overrun)   None
2 Active    None
3 Active    None
4 Active    None
5 Active    None
6 Inactive    None
7 Inactive    None
8 Inactive    None
9 Inactive    None
10 Inactive    None
11 Inactive    None
12 Inactive    None
13 Inactive    None
14 Inactive    None
15 Inactive    None
16 Active    100% None
17 NORMAL(0h)    NORM None
18 NORMAL(0h)    NORM None
F Active    None

Last Status Reset: 02/15/04 18:36:21
*>>

Figure 8.29

Active State for (Overrun)

Courtesy of NationalSwitchgear.com

«
...
235
236
237
238
239
...
»

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

Brand: CAME Pages: 19

Protege PRT-PX16-PCB

Brand: ICT Pages: 34

Brand: Wintech Pages: 21

Brand: VCS Pages: 118

Digital Encoder Plus

Brand: IDT Pages: 98

Compact NVR-AS 4000

Brand: IndigoVision Pages: 38

Brand: RAID Pages: 80

KÜHLER H2O 920

Brand: Antec Pages: 6

IA611 Xplained Pro

Brand: Knowles Pages: 14

Brand: ENERMAX Pages: 33

Brand: Pilz Pages: 12

Brand: ALIBI Pages: 232

Brand: Qlogic Pages: 2

Brand: PairGain Pages: 48

GigaVUE H TA100-CXP

Brand: Gigamon Pages: 115

Gen3 Ethernet Module

Brand: NCD Pages: 18

Brand: ZALMAN Pages: 12

Brand: Martin Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands