manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Instruction Manual

The Schweitzer Engineering SEL-2032 Instruction Manual is a comprehensive guide designed to assist users in operating this cutting-edge product efficiently. With step-by-step instructions and detailed explanations, this manual is available for free download on our website. Unlock the full potential of your SEL-2032 today at manualshive.com.

Share
Download
background image

9.39

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Protocols

Serial Distributed Network Protocol (Serial DNP3)

Internal Indication Object

Within the Internal Indications (IIN) object, the bits are used as specified 
within the DNP3 standard. When TIME_SRC is equal to DNP3 within the 
Global settings, the SEL-2032 requests time synchronization every 15 
minutes. Bit 4 within the IIN object will be set and remain set until the 
SEL-2032 receives a time synchronization. If the SEL-2032 receives a time 
synchronization, it will clear the bit and then set it again 15 minutes later. The 
SEL-2032 does not have local/remote states, so the local/remote bit indicates 
whether or not SEL

OGIC

 control equations are running. If SEL

OGIC

 control 

equations are not running, the status is indicated as local since the DNP3 data 
will not be updated by 

SET M

 while SEL

OGIC

 control equations are not 

running.

Timing

Maximum data-link response time (without confirmation):

150 ms.

Maximum class 0 request response time (without confirmation):

300 ms.

Maximum data-link confirm time:

150 ms.

Maximum application confirm time (without data-link confirmation):

50 ms.

Time 
Synchronization

When TIME_SRC is equal to DNP3 within the Global settings, you can 
perform Time Synchronization via DNP3 by executing a write to the Date/
Time object (object 50). The DNP3 protocol assumes that the time value sent 
by the master device is the time at which the first bit of the first byte of the 
write request is received by the slave (SEL-2032). It is the responsibility of the 
master to account for transmission delay between sending the request and the 
SEL-2032 receipt of the request. In many systems this transmission delay will 
be 0. For example, in a simple point-to-point connection, the moment the first 
bit is transmitted by the master, it is received by the slave device. In 
configurations where the communication link may introduce delays, the 
master may perform a delay measurement command and then calculate the 
transmission delay based on the result of the delay measurement. The master 
can then add this calculated transmission delay time to the time value that it 
sends to the SEL-2032 when it writes the time. When time synchronization is 
performed, the SEL-2032 will synchronize itself to within 5 ms (+3/–2) of the 
given time. When the delay measurement command is performed, the value 
reported by the SEL-2032 is accurate to 10 ms (+5/–5). So, disregarding errors 
external to the SEL-2032, a time synchronization that uses a Delay 
Measurement calculation is accurate to within 15 ms (+8/-7).

Event Data

The SEL-2032 generates DNP3 event data in one of two ways. For devices 
that support the SEL Fast SER protocol, the SEL-2032 processes incoming 
SER data to provide DNP3 events (Object 2 data) with time stamps generated 

Port 4-17 Not Shown

93

18:BR1

Pulse 18:SBR1

Pulse 18:CBR1

Pulse 18:SBR1

18:Pulse CBR1

18:Pulse CBR1

18:Pulse SBR1

94

18:RB1–RB2

Pulse 18:SRB2

Pulse 18:SRB1

Pulse 18:SRB2

18:Pulse SRB1

18:Pulse SRB2

18:Pulse SRB1

95

18:RB3–RB4

Pulse 18:SRB4

Pulse 18:SRB3

Pulse 18:SRB4

18:Pulse SRB3

18:Pulse SRB4

18:Pulse SRB3

96

18:RB5–RB6

Pulse 18:SRB6

Pulse 18:SRB5

Pulse 18:SRB6

18:Pulse SRB5

18:Pulse SRB6

18:Pulse SRB5

97

18:RB7–RB8

Pulse 18:SRB8

Pulse 18:SRB7

Pulse 18:SRB8

18:Pulse SRB7

18:Pulse SRB8

18:Pulse SRB7

Table 9.23

Example Control Points 

 (Sheet 2 of 2)

DNP3 

Object 

12 Index

SEL-2032 

Control 

Points

DNP3 Object 12 Control Operation Code

Latch On

Latch Off

Pulse On

Pulse Off

CLOSE

TRIP

Courtesy of NationalSwitchgear.com

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

Laird OL 4503 Specification And User Manual preview
OL 4503
Brand: Laird Pages: 36
Commell LS-570 User Manual preview
LS-570
Brand: Commell Pages: 58
Dialogic EDP-10 Quick Install Manual preview
EDP-10
Brand: Dialogic Pages: 2
vPipes Uilleann Quick Start Manual preview
Uilleann
Brand: vPipes Pages: 3
ROE EVISON HD101 User Manual preview
EVISON HD101
Brand: ROE Pages: 41
ZALMAN RESERATOR 1 Manual preview
RESERATOR 1
Brand: ZALMAN Pages: 22
Dantel 46020-38 Installation & Operation Manual preview
46020-38
Brand: Dantel Pages: 62
Infoblox Trinzic 100 Installation Manual preview
Trinzic 100
Brand: Infoblox Pages: 13
ACTi GNR-310 Quick Installation Manual preview
GNR-310
Brand: ACTi Pages: 12
Rane HAL1x System Installation Manual preview
HAL1x
Brand: Rane Pages: 128
Acard AEC-6885 User Manual preview
AEC-6885
Brand: Acard Pages: 34
Shure DFR22 Software Manual preview
DFR22
Brand: Shure Pages: 113
Ubiquiti UniFi WiFi BaseStation XG Quick Start Manual preview
UniFi WiFi BaseStation XG
Brand: Ubiquiti Pages: 19
CG Emotron OSTO 100 Instruction Manual preview
Emotron OSTO 100
Brand: CG Pages: 112
Xyclop XC-4CH-NVR-1TB User Manual preview
XC-4CH-NVR-1TB
Brand: Xyclop Pages: 144
Silvertel Ag102 User Manual preview
Ag102
Brand: Silvertel Pages: 9
Barracuda CloudGen Firewall Revision preview
CloudGen Firewall
Brand: Barracuda Pages: 8
Kordis NCB210X2-DS-AB Datasheet preview
NCB210X2-DS-AB
Brand: Kordis Pages: 31

Brands by name

Popular brands

Load more brands