Schweitzer Engineering SEL-2032 Instruction Manual Download Page 43 | Manualshive

Page: 43 / 354

background image

1.27

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Introduction and Specifications

Details

SEL-2030 and
SEL-2032
Comparison

The SEL-2032 has several features not included in the SEL-2030. Basic
operation and settings are identical in the SEL-2030 and SEL-2032.

Robust Design

The SEL-2032 is designed to provide reliable service in a wide variety of
electrical, physical, and environmental conditions.

Wide Temperature Operating Range

The SEL-2032 is designed for operation with an ambient temperature between
–40



and +185



F (–40



and +85



C). Plug-in protocol cards may have more

restrictive temperature ranges. Check the instruction manual of any plug-in
protocol card to confirm its temperature range.

Wide Voltage Range Power Supply

Two power supply voltage ranges are available. The 125/250 volt power
supply will operate with a voltage range of 85–350 Vdc or 85–264 Vac. The
24/48 volt power supply will operate with a voltage range of 20–60 Vdc.

Meets Tough IEEE and IEC Standards

The SEL-2032 is designed to meet tough IEEE and IEC electrical,
environmental, and vibration standards, making the SEL-2032 suitable for
application in hostile environments such as substations and power plants, in
relay and control houses, or in outdoor cabinets and enclosures.

Table 1.2

Differences Between the SEL-2030 and SEL-2032

SEL-2030

SEL-2032

Optional 2 MB archive memory.

1.75 MB archive memory included.

Adequate setting storage
space for most applications.

Significantly increased
setting storage space for heavy
SET M math/movement setting use.

DNP3 event time stamps
assigned by SEL

-

2030.

SER quality time stamps
from SEL IEDs that support
Fast SER available for SEL-2032

DNP3.

No nonvolatile storage.

Ten nonvolatile storage
registers per User region.

Courtesy of NationalSwitchgear.com

«
...
41
42
43
44
45
...
»

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

Brand: Lauterbach Pages: 61

Brand: X-Micro Pages: 9

Brand: X-Micro Pages: 19

SuperServer 5019S-L

Brand: Supermicro Pages: 61

Brand: Time domain Pages: 64

Brand: ZALMAN Pages: 7

EK-Quantum Momentum ROG Rampage VI Encore

Brand: EK Pages: 11

UM10301 PCA8565

Brand: NXP Semiconductors Pages: 54

Wisenet XRN-6410RB2-24TB

Brand: Hanwha Techwin Pages: 124

Brand: Z-Wave Pages: 42

Brand: Thecus Pages: 90

Brand: Axtrinet Pages: 49

Brand: VALKYRIE Pages: 26

Brand: ProCurve Pages: 406

Brand: ADTRAN Pages: 162

Brand: Omron Pages: 86

Brand: Omron Pages: 32

Brand: UNA AUTOMATION Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands