Schweitzer Engineering SEL-2032 Instruction Manual Download Page 44

Page: 44 / 354

1.28

SEL-2032

Communications Processor

Instruction Manual

Date Code 20120126

Introduction and Specifications

Specifications

General Specifications

Rear Screw-Terminal Tightening Torque

Minimum:

0.8 Nm (7-in-lb)

Maximum:

1.4 Nm (12-in-lb)

Terminal Connections

Terminals or stranded copper wire. Ring terminals are

recommended. Minimum temperature rating of 105°C.

Power Supply

Rated:

125/250 Vdc or Vac

Range:

85–350 Vdc or 85–264 Vac

Burden:

<25 W

Rated:

48/125 Vdc or 125 Vac

Range:

38–200 Vdc or 85–140 Vac

Burden:

<25 W

Rated:

24/48 Vdc

Range:

20–60 Vdc polarity dependent

Burden:

<25 W

Output Contacts

Make:

30 A

Carry:

6 A

MOV Protected:

250 Vac RMS/330 Vdc Continuous

Note:

Make per

IEEE C37.90 Tripping Output Performance

Requirements

. MOV per IEC 60255-0-20: 1974, using the

simplified method of assessment. 50 A for one second.

Optoisolated Input Ratings

Level-Sensitive Inputs (16 Inputs Total, with Optional I/O Board)

24 Vdc:

Operate (Pickup) 15–30 Vdc

48 Vdc:

Operate (Pickup) 38.4–60 Vdc;

Dropout 28.8 Vdc

125 Vdc:

Operate (Pickup) 105–150 Vdc;

Dropout 75 Vdc

250 Vdc:

Operate (Pickup) 200–300 Vdc;

Dropout 150 Vdc

Note:

The optoisolated inputs each draw 4 mA when nominal

control voltage is applied.

Serial Ports

1 Front-panel/16 Rear-panel Ports, DB-9 Connectors, MOV

Protected.

Time-Code Input

Connector:

Female BNC and Pin-in

Port 15 Connector

Time Code:

Modulated IRIG-B 1000

Vdc Isolation

Demodulated IRIG-B

TTL-Compatible.

Note:

Automatically sets SEL-2032 Real-time Clock/Calendar

Time-Code Output

Pinout:

Pin 4 TTL-level Signal
Pin 6 Chassis Ground Reference

Connectors:

All 16 Rear DB-9 Port Connectors

Note:

Outputs are generated from IRIG-B input (when present) or

generated by CPU from real-time clock/calendar.

Operating Temperature Range

–40° to +85°C (–40° to +185°F)

Unit Weight

3U Rack Unit Height: 3.50 kg (7 lb, 12 oz)

Production Dielectric Strength

Power Supply,

Logic Inputs, and
Output Contacts:

3100 Vdc for 10 s.

Type Tests and Standards

Electromagnetic Compatibility Immunity

Electrostatic

Discharge:

IEC 60255-22-2:1996
[BS EN 60255-22-2:1997]
IEC 61000-4-2:1995
[EN 61000-4-2:1995]

2, 4, 6, 8 kV contact

2, 4, 8, 15 kV air

Fast Transient/

Burst:

IEC 60255-22-4:1992

4 kV at 2.5 kHz and 5 kHz

IEC 61000-4-4:1995
[EN 61000-4-4:1995]

4 kV, 2.5 kHz power supply
2 kV, 5 kHz I/O, signal, data, control lines

Radiated Radio

Frequency:

IEC 60255-22-3:1989

10 V/m
Exception: 4.3.2.2 Freq. Sweep Approx.
with 200 Freq. Steps Per Octave

IEC 801-3:1984

10 V/m
Exceptions: 9.1 Freq. Sweep Approx.
with 200 Freq. Steps Per Octave

IEEE C37.90.2-1995

35 V/m

Surge Withstand

Capability:

IEC 60255-22-1:1988

2.5 kV Peak Common Mode
1.0 kV Peak Differential Mode

IEEE C37.90.1-1989

3.0 kV Oscillatory
5.0 kV Fast Transient

Environmental

Cold:

IEC 60068-2-1:1990 + A1:1993 + A2:1994
[BS EN 60068-2-1:1993 + REAF:2005]

16 hr at –40°C

Damp Heat,

Cyclic:

IEC 60068-2-30:1980

25°C–55°C, 6 Cycles,
Relative Humidity: 95%
Exceptions: 6.3.3 Humidity Not Less
than 94%

Dry Heat:

IEC 60068-2-2:1974 + A1:1993 + A2:1994
[BS EN 60068-2-2:1993 + REAF:2005]

16 hr at 85°C

Vibration:

EIC 60255-21-1:1988
[BS EN 60255-21-1:1996 + A1:1996]

Class 1 Endurance
Class 2 Response

IEC 60255-21-2:1988
[BS EN 60255-21-2:1996 +A1:1996]

Class 1 Shock Withstand, Bump
Class 2 Shock Response

IEC 60255-21-3:1993
[BS EN 60255-21-3:1995 +A1: 1995]

Class 2 Quake Response

Safety

Dielectric

Strength:

IEC 60255-5:1977
IEEE C37.90-1989

2500 Vac on Contact Inputs, Contact

Outputs, Analog Inputs

3100 Vdc on Power Supply
1 min Test

Impulse:

IEC 60255-5:1977

0.5 J, 5 kV

Certifications

ISO: Designed and manufactured using ISO 9001 certified quality

program.

Real-Time Clock/Calendar

Battery Type:

IEC No. BR2335 Lithium

Battery Life:

10 years

Clock Accuracy:

±20 min/yr @ 25°C

(without power applied)

±1 min/yr @ 25°C (with

power applied)

±1 ms with IRIG-B time-code input

Courtesy of NationalSwitchgear.com

Summary of Contents for SEL-2032



































































































































































































































































































































































Search results

Summary of Contents for SEL-2032

Reviews:

Related manuals for SEL-2032

Brands by name

Popular brands

Schweitzer Engineering SEL-2032, Instruction Manual

Search results

Summary of Contents for SEL-2032

Reviews:

Related manuals for SEL-2032

Brands by name

Popular brands