Schweitzer Engineering SEL-2032 Instruction Manual Download Page 114 | Manualshive

Page: 114 / 354

background image

4.10

SEL-2032

Communications Processor

Instruction Manual

Date Code 20120126

SEL

OGIC

Control Equations

Communications and Triggered Messages

Communications and Triggered Messages

Whenever the SEL-2032 transmits a triggered message to an IED on one of its ports,
it increments the LOCAL:NUM_MESG message counter in the database. If the
SEL-2032 does not receive a response to the triggered message, it will set the port
status to Inactive (bit 5 of LOCAL:PORT_STATUS and LOCAL:INAC) and
increment the LOCAL:BAD_MESG message counter in the database. If, while the
port status is Inactive, the SEL-2032 transmits ten consecutive messages without
receiving a response, it will also set port status to Port Communication FAIL (bit 10
of LOCAL:PORT_STATUS). If PARSE

x

= IGNORE and the SEL-2032 does not

receive a response to a transmitted message, it will not set port status to Inactive, nor
increment the LOCAL:BAD_MESG message counter in the database.

If the port device type, DEVICE = OTHER or SEL, the SEL-2032 will
transmit every triggered message regardless of the port status. In general, the
SEL-2032 will only retransmit a message if it has been retriggered. However,
if the triggered message is a Binary 20message, e.g., Binary 20METER, or
SEL Fast Message Read (such as 20ENERGY), and port status is Inactive, the
SEL-2032 will retransmit the message until it reestablishes communication
with the IED. Furthermore, if the device type is DEVICE = SEL and port
status is Inactive, for each triggered user-defined message or ASCII
20message, (e.g., ASCII 20METER) message, the SEL-2032 will also
transmit a CR/LF (Carriage Return with Linefeed).

For DEVICE = SEL IED, if an ASCII Operate or a Fast (Binary) Operate is
triggered while the port status is Inactive, the Operate is issued and the trigger is
cleared. The SEL-2032 will retransmit the Operate only if it has been retriggered.

The SEL-2032 will clear the Port Inactive and Communication FAIL statuses
if any of the following occurs:

If the port DEVICE = OTHER IED,

➤

The SEL-2032 receives a response of at least one character,
PARSE

x

is not set to IGNORE, and it can successfully parse

the response from the IED.

➤

The SEL-2032 receives a response of at least one character and
the PARSE

x

is set to IGNORE. Conversely, if the PARSE

x

is

set to IGNORE and the IED does not respond with at least one
character, the port Inactive and Communication FAIL statuses
will

not

be cleared.

➤

The SEL-2032 receives an unsolicited response of at least one
character.

If the port DEVICE = SEL IED,

➤

The SEL-2032 successfully performs a binary data collection
such as a 20METER or 20DEMAND.

Note: If the SEL-2032 issues an Enable/Disable Unsolicited
SER message and does not receive a response, the port status
will remain unchanged.

➤

The SEL-2032 receives an unsolicited response of at least one
character.

Whenever the port Inactive status is cleared, the SEL-2032 will transmit the
contents of the STARTUP string.

Courtesy of NationalSwitchgear.com

«
...
112
113
114
115
116
...
»

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

Brand: LAWO Pages: 154

Brand: Palm Pages: 4

COMSPHERE 3800 Series

Brand: Paradyne Pages: 88

COMSPHERE 3800PLUS

Brand: Paradyne Pages: 5

Optane M Series

Brand: Intel Pages: 59

Brand: DAD Pages: 32

Brand: Commell Pages: 9

Brand: ICP DAS USA Pages: 62

Brand: Comway Pages: 20

Brand: ekwb Pages: 11

Brand: Lindy Pages: 12

MP5S Plus Writer

Brand: SONIX Pages: 23

Brand: H3C Pages: 34

Brand: ENERMAX Pages: 33

ExtremeCloud Appliance E1120

Brand: Extreme Networks Pages: 219

Brand: Mitsubishi Pages: 188

Brand: Allen-Bradley Pages: 76

Brand: Disc Makers Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands