Schweitzer Engineering SEL-2032 Instruction Manual Download Page 155 | Manualshive

Page: 155 / 354

background image

7.7

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Settings

Port Configuration (SET P) and Communication Settings

Figure 7.2

EIA-232 Character Format

Auto-
Configuration

Auto-configuration, or automatic configuration, is the process of collecting
information from the connected SEL device that describes available
communications capabilities. This information includes the firmware ID,
device type, and available remote bits, breaker bits, and “20” messages. You
can use the

AUTO

command at any time to display a summary of collected

information.

TIMEOUT

Port Time-out in minutes (0–120).

The time-out setting is used for two different functions. After
a set amount of idle time expires with the port in transparent mode,
transparent mode is automatically terminated. On Master ports, if this
time expires with the port idling, any in-process command is
terminated and the access level is reduced to Level 0. The time-out
action also disconnects LMD communications and hangs up the
modem if it is connected. A value of 0 disables time-out.

Note:

Use a non-zero time-out value for modem ports. If the

modem connection is unintentionally interrupted, you can call
and successfully reconnect TIMEOUT minutes later.

ECHO

Echo received characters (Y/N).

Master Port only. The echo option allows you to decide whether or
not you wish the SEL-2032 to provide character echo to a master
device (only printable characters are echoed). ECHO is always Y
(Yes) for Port F.

AUTO_HELP

Automatic help messages enabled
(Y/N).

Default setting is AUTO_HELP=Y. You can disable Auto-Help
on a port by setting AUTO_HELP=N. Auto-Help provides correct
commands and command syntax messages when you enter an
incorrect command or command syntax. If you disable Auto-Help on
a Master port, you can still request help with the

HELP

command.

TERTIME1

First delay time (0–600 seconds).

You enter a time that a port must be idle before checking for the
termination string. For a description of transparent communications,
see

Transparent Communications on page 7.8

TERSTRING

Prompt

. Termination string.

You enter a string that terminates transparent communications.
The default is \004, the code for

<Ctrl+D>

. For a description of

transparent communications, see

Transparent Communications

TERTIME2

Second delay time (0–600 seconds).

You enter a time the port must be idle, after receiving
the termination string, before terminating transparent
communications. For a description of transparent communications,
see

Transparent Communications

.

Table 7.1

Port Configuration (SET P) Settings Information

(Sheet 5 of 5)

Setting

Comment

Description

EIA-232 Character

7 or 8

Databits

Start Bit

Optional

Parity

1 or 2

Stopbits

Courtesy of NationalSwitchgear.com

«
...
153
154
155
156
157
...
»

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

Brand: EAW Pages: 2

Brand: SAF Pages: 30

Brand: Dahua Pages: 6

SRCSASBB8I - RAID Controller

Brand: Intel Pages: 36

Brand: Kaptia Pages: 14

4 Channel Input Buffer Board SDAIBB

Brand: B&B Electronics Pages: 22

Brand: PaloAlto Networks Pages: 28

Brand: Xilinx Pages: 27

Brand: Magewell Pages: 10

Brand: Z3 Technology Pages: 18

Brand: Keithley Pages: 108

Brand: Digital Equipment Pages: 90

Brand: Vivotek Pages: 46

Brand: Transition Networks Pages: 1

Brand: LevelOne Pages: 61

GPX-N 1080Ti-M23

Brand: Alphacool Pages: 4

Brand: Crown Pages: 7

Brand: Transition Networks Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands