manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Instruction Manual

The Schweitzer Engineering SEL-2032 Instruction Manual is a comprehensive guide designed to assist users in operating this cutting-edge product efficiently. With step-by-step instructions and detailed explanations, this manual is available for free download on our website. Unlock the full potential of your SEL-2032 today at manualshive.com.

Share
Download
background image

8.23

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Serial Port Communications and Commands

Command Set

The SEL-2032 settings become invalid when the SEL-2032 copies ROM 
default settings into EEPROM. This problem occurs when new code is 
installed in the SEL-2032. You use the 

SET C

 command to change the 

settings to VALID. For any unexpected self-test failure, you should contact the 
factory immediately to get the unit repaired.

Port Status Information

Status.

 The Port Status Column of the report indicates, for each port, whether 

the port is Unused, Active (in a normal active state), Inactive (not responding), 
pInactive (in an inactive state with a power-up auto-configuration pending), 
ConfigFail (in a power-up auto-configuration failure state), Trans 

n

 

(communicating transparently with some other port, e.g., Trans 7), Trans C 

yyyy

 (communicating transparently with card C to network device 

yyyy

), or 

Broadcast (communicating to all IED ports simultaneously).

A “dropped character” diagnostic appended to the port Status indicates that 
the serial port has been unable to process characters. This condition could 
occur if a transparent connect between two ports is created with different baud 
rates and flow control is disabled. In this case, the faster port could 
theoretically transfer more data than the slower baud rate port could process. 
When this occurs “(overrun)” will be appended to the slower baud rate port. 
Overrun will remain appended to the port status until STATUS Clear is issued, 
loss of power occurs, or the SEL-2032 is re-initialized.

Plug-in card status and status code are reported for Ports 17 and 18. See the 
instruction manual for the plug-in card for information about these 
indications. For cards that support virtual terminal connections, an additional 
line is appended for active virtual terminal connections; the status can include 
Master VTn (virtual terminal master session) or Trans PVtn (virtual terminal 
transparent connection to Port P).

Success Rate.

 The Success Rate column indicates the percentage of error-free 

messages received; errors could be due to checksum failure or unexpected 
data items. The Success Rate is reset when you issue a 

STATUS CLEAR

 or 

STATUS RESET

 command, or you issue a 

SET P

 command for a port.

In the SEL-2032, additional plug-in card status is provided in this column. 
The value will be NORM if everything is working as expected. The value will 
be FAIL if the card quits responding to the SEL-2032.

SET M. 

The SET M column indicates the state of SET M settings. ‘None’ 

indicates that there are not SET M settings on the port or that the SEL-2032 is 
still doing power-up initialization and the settings have not yet compiled. 
‘Running’ indicates that SET M settings exist and are running on the 

BATTERY

OK 

FAIL

Battery-backed clock
battery was OK on last power-up. 

Bad date or time reported by
battery-backed clock on last power-up.
This is probably due to a low battery.

IRIG-B Input

Absent 

Present

No IRIG-B input signal is detected. 

IRIG-B input signal is present.

I/O Board

Absent 

Installed

No I/O board is installed. 

I/O board is installed.

Table 8.6

Status Report Description 

 (Sheet 2 of 2)

Parameter

Status Displayed

Explanation

Courtesy of NationalSwitchgear.com

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

Quatech DS-3000 User Manual preview
DS-3000
Brand: Quatech Pages: 27
Ratoc Systems SCSI PC Card REX-9530V Product Manual preview
SCSI PC Card REX-9530V
Brand: Ratoc Systems Pages: 30
Garland INT10G10SP2 User Manual preview
INT10G10SP2
Brand: Garland Pages: 6
Idis DR-8400 Installation Manual preview
DR-8400
Brand: Idis Pages: 31
HARTING HAIIC MICA Hardware Development Manual preview
HAIIC MICA
Brand: HARTING Pages: 13
red lion Yaskawa 2000 Information Sheet preview
Yaskawa 2000
Brand: red lion Pages: 5
ADC HiGain H2TU-R-402 List 7A Quick Installation preview
HiGain H2TU-R-402 List 7A
Brand: ADC Pages: 7
Renesas H8S/2633 User Manual preview
H8S/2633
Brand: Renesas Pages: 28
Ubiquiti PowerBeam PBE-5AC-400-ISO Quick Start Manual preview
PowerBeam PBE-5AC-400-ISO
Brand: Ubiquiti Pages: 23
MF DIGITAL 5200 Live Series EventCD Operator'S Manual preview
5200 Live Series EventCD
Brand: MF DIGITAL Pages: 21
ZALMAN RESERATOR2 Installation And Operational Manual preview
RESERATOR2
Brand: ZALMAN Pages: 18
Procool SP480 Series Instructions preview
SP480 Series
Brand: Procool Pages: 2
Cypress Semiconductor CY7C1410JV18 Specification Sheet preview
CY7C1410JV18
Brand: Cypress Semiconductor Pages: 26
National Semiconductor Data Capture Board CLC-CAPT-PCASM User Manual preview
Data Capture Board CLC-CAPT-PCASM
Brand: National Semiconductor Pages: 15
ADC 150-204-100-03 User Manual preview
150-204-100-03
Brand: ADC Pages: 29
IBA ibaBM-FOX-i-3o-D Manual preview
ibaBM-FOX-i-3o-D
Brand: IBA Pages: 13
Adaptec Ultra Wireless AWN-8030 User Manual preview
Ultra Wireless AWN-8030
Brand: Adaptec Pages: 57
Rohm BD7682FJ-EVK-301 Quick Start Manual preview
BD7682FJ-EVK-301
Brand: Rohm Pages: 6

Brands by name

Popular brands

Load more brands