manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Instruction Manual

The Schweitzer Engineering SEL-2032 Instruction Manual is a comprehensive guide designed to assist users in operating this cutting-edge product efficiently. With step-by-step instructions and detailed explanations, this manual is available for free download on our website. Unlock the full potential of your SEL-2032 today at manualshive.com.

Share
Download
background image

1.21

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Introduction and Specifications

Functions

MEM

The 

MEM

 command indicates the status of the RAM, Shared RAM, 

EEPROM, and Flash memory pools. You can use this to determine if you are 
in danger of running out of memory.

Data Parsing Options

The SEL-2032 database stores data that are parsed, or separated, into the 
smallest useful items. Parsing data in the SEL-2032 reduces communication 
and processing burdens for other devices or systems that use these data by 
permitting them to request and transfer only the specific data they need.

“20” Message Response

The SEL-2032 automatically parses data that are recognized. These data are 
requested using the “20” message format. The type of response will depend on 
the attached device's capability. If it has Fast Meter capability, the responses to 
20METER messages are in binary format and the responses to 20DEMAND 
and 20TARGET messages may also be in a binary format.

Non-“20” Message Response

Message responses that are not recognized as SEL data can be ignored or 
parsed by one of five techniques:

ASCII Integer (Parse = 1).

Parses numbers only.

ASCII Float (Parse = 2).

Parses numbers only, including decimal points.

Character String (Parse = 3).

Retains all characters.

Integer String (Parse = 4).

Stores each pair of received bytes in a register, 

most-significant-byte first.

Integer String with XON/XOFF encoding (Parse = 5).

Same as Integer 

String except special 2-byte encoding sequences are used to represent XON 
(11h) and XOFF (13h) characters.

Flexible Parsing (Parse = 6).

Parses received bytes based on the DECODE 

equation. This option is especially useful when the incoming data 
types can be either numbers or text.

Network Gateway

The SEL-2032 has two plug-in slots where you can install protocol cards. This 
allows the SEL-2032 to connect up to 16 serial devices to two high-speed 
networks. Contact SEL or check our Web site at www.selinc.com for 
information on available network cards.

The SEL-2032 also supports virtual terminal connections through the optional 
communications card slots. For example, with an SEL-2701 Ethernet 
Processor installed, Ethernet users can establish Telnet sessions through the 
card, issue a 

PORT

 command, and communicate with an IED connected to 

the SEL-2032.

Courtesy of NationalSwitchgear.com

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

ABB i-bus KNX IPR/S 3.5.1 Product Manual preview
i-bus KNX IPR/S 3.5.1
Brand: ABB Pages: 44
D-Link DXS-3610-54S Quick Installation Manual preview
DXS-3610-54S
Brand: D-Link Pages: 38
D-Link Web Smart DES-1210-28P Selection Manual preview
Web Smart DES-1210-28P
Brand: D-Link Pages: 6
D-Link xStack Storage DSN-4000 Series Manual preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 23
D-Link Express EtherNetwork DI-604 Brochure preview
Express EtherNetwork DI-604
Brand: D-Link Pages: 7
D-Link xStack Storage DSN-4000 Series Cli User'S Manual preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 97
Stanwax Laser ILDA Gem Laser projector tool Instructions preview
ILDA Gem Laser projector tool
Brand: Stanwax Laser Pages: 3
hilscher CIFX 104 User Manual preview
CIFX 104
Brand: hilscher Pages: 154
Renesas H8/3864 Series User Manual preview
H8/3864 Series
Brand: Renesas Pages: 20
IDT Tsi310TM User Manual preview
Tsi310TM
Brand: IDT Pages: 207
Supermicro Optane Persistent Memory 200 Series User Manual preview
Optane Persistent Memory 200 Series
Brand: Supermicro Pages: 54
Idis DR-6308P Quick Manual preview
DR-6308P
Brand: Idis Pages: 20
Ubiquiti UniFi LED ULED-AT Quick Start Manual preview
UniFi LED ULED-AT
Brand: Ubiquiti Pages: 16
ekwb 3831109826140 User Manual preview
3831109826140
Brand: ekwb Pages: 11
SriHome NVS001B Quick Operation Manual preview
NVS001B
Brand: SriHome Pages: 12
Xantech IR-X10 Installation Instructions Manual preview
IR-X10
Brand: Xantech Pages: 16
AES BeBoPr++ User Manual preview
BeBoPr++
Brand: AES Pages: 44
Aleratec 260206 Quick Start Manual preview
260206
Brand: Aleratec Pages: 16

Brands by name

Popular brands

Load more brands