Schweitzer Engineering SEL-2032 Instruction Manual Download Page 327 | Manualshive

Page: 327 / 354

background image

B.5

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Firmware Upgrade Instructions

Upgrade Warning

Step 6. When the transfer is complete, the SEL-203

x

and SEL-27xx

indicate whether they received the new code successfully.

➢

If the transfer was not successful, repeat

Step 5

.

➢

When the transfer succeeds, repeat

Step 5

if you are

upgrading multiple programs and/or multiple protocol
cards.

➢

Once all upgrades are complete, enter the

EXIT

command to return the SEL-203

x

and associated

protocol cards to normal operation.

Step 7. To communicate with the SEL-203

x

, use the baud rate you used

in

Step 1

to establish communications.

Step 8. Study the documentation that came with the upgrade to

determine if you need to make any settings changes.

New firmware versions may contain new functions and new
settings. It may be necessary to modify settings to achieve
operation that is the equivalent of operation before the upgrade.

Step 9. Check the settings and operation of your SEL-203

x

by

executing the

STATUS

command and examining the results. If

the status is not as you expect, contact SEL for assistance.

Step 10. Because the SEL-203

x

dynamically allocates resources, you

must perform a test to verify that the settings and operation of
the SEL-203

x

are correct. Remove and reapply power to the

SEL-203

x

and observe the startup sequence of the SEL-203

x

.

After the startup is complete, connect to the SEL-203

x

and

execute the

STATUS

command to verify proper operation. If

the status is not as you expect, contact SEL for assistance.

Upgrade Warning

SEL-2701 firmware releases prior to R108 are not compatible with SEL

BOOT

version R102. A “SLBT FAIL” (Hex 0x0004) message may appear if a

STA

tus command is issued when SEL

BOOT

R102 is used with firmware

releases R100–R105.

Factory Assistance

We appreciate your interest in SEL products and services. If you have
questions or comments, please contact us at:

Schweitzer Engineering Laboratories, Inc.
2350 NE Hopkins Court
Pullman, WA 99163-5603 USA
Telephone: +1.509.332.1890
Fax: +1.509.332.7990
Internet: www.selinc.com
Email: [email protected]

Courtesy of NationalSwitchgear.com

«
...
325
326
327
328
329
...
»

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

Brand: dbx Pages: 8

Brand: Cabletron Systems Pages: 21

Brand: A10 Pages: 52

Brand: Blackrock Microsystems Pages: 27

Brand: Usr Pages: 2

PCI-6110E/6111E

Brand: National Instruments Pages: 113

Brand: Moxa Technologies Pages: 51

Brand: Supermicro Pages: 131

LinkStation 500

Brand: Buffalo Pages: 139

Service Aggregation Router 7705

Brand: Alcatel-Lucent Pages: 20

Brand: Tektronix Pages: 143

Brand: Actelis Networks Pages: 50

CCR2004-16G-2S+PC

Brand: MikroTik Pages: 20

Brand: MSI Pages: 5

Brand: IntraServer Technology Pages: 16

Brand: Kenwood Pages: 10

Brand: Kenwood Pages: 12

Brand: Artesyn Embedded Technology Pages: 70

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands