Schweitzer Engineering SEL-2032 Instruction Manual Download Page 300 | Manualshive

Page: 300 / 354

background image

9.56

SEL-2032

Communications Processor

Instruction Manual

Date Code 20120126

Protocols

Distributed Network Protocol 3.0 (DNP3) LAN/WAN

Custom Data Mapping

NOTE:

When DNPMAP = CUSTOM,

the SEL-2032 stores the most recent
value of all DNP points in its STATE
region. Like the User region, the
STATE region has one timestamp,
which indicates the time at which the
collective data was last updated.
However, the STATE region also has
an SER queue. It is the SER queue that
provides a per point history of time-
stamped changes within the region.
For this reason, you must set DNPMAP
= CUSTOM if you want to preserve
SER time stamps from an attached
IED all the way through to the DNP
Master.

By setting the DNPMAP parameter to CUSTOM, you have the ability to
specify the DNP3 data points available for up to 10 unique master sessions
using any of 5 distinct data maps. The most efficient way to set the DNP3 Map
mode and assign data maps to DNP3 masters is to use the SEL-5020 Settings
Assistant.

71

1:RB16/RB15

Pulse 1:SRB16

Pulse 1:SRB15

Pulse 1:SRB16

Pulse 1:SRB15

Pulse 1:SRB16

Pulse 1:SRB15

72

2:RB02/RB01

Pulse 2:SRB02

Pulse 2:SRB01

Pulse 2:SRB02

Pulse 2:SRB01

Pulse 2:SRB02

Pulse 2:SRB01

•

•

•

207

18:RB16/RB15

Pulse 18:SRB16 Pulse 18:SRB15 Pulse 18:SRB16 Pulse 18:SRB15 Pulse 18:SRB16

Pulse 18:SRB15

208

1:BR1

Pulse 1:CBR1

Pulse 1:SBR1

Pulse 1:SBR1

Pulse 1:CBR1

Pulse 1:SBR1

Pulse 1:CBR1

209

1:BR2

Pulse 1:CBR2

Pulse 1:SBR2

Pulse 1:SBR2

Pulse 1:CBR2

Pulse 1:SBR2

Pulse 1:CBR2

210

1:BR3

Pulse 1:CBR3

Pulse 1:SBR3

Pulse 1:SBR3

Pulse 1:CBR3

Pulse 1:SBR3

Pulse 1:CBR3

•

•

•

223

1:BR16

Pulse 1:CBR16

Pulse 1:SBR16

Pulse 1:SBR16

Pulse 1:CBR16

Pulse 1:SBR16

Pulse 1:CBR16

224

2:BR1

Pulse 2:CBR1

Pulse 2:SBR1

Pulse 2:SBR1

Pulse 2:CBR1

Pulse 2:SBR1

Pulse 2:CBR1

•

•

•

463

16:BR16

Pulse 16:CBR16 Pulse 16:SBR16 Pulse 16:SBR16 Pulse 16:CBR16 Pulse 16:SBR16

Pulse 16:CBR16

Table 9.30

SEL-2032 DNP3 Over Ethernet Object 12 Control Point Operation, DNPMAP = AUTO, DNPPAIR = Y

(Sheet 2 of 2)

DNP3

Indices

(Control

Pt. IDs)

Control Points

Trip / Close Pairs

Code Selection Operation

Close (0x4X)

Trip (0x8X)

Latch On (3)

Latch Off (4)

Pulse On (1)

Pulse Off (2)

Courtesy of NationalSwitchgear.com

«
...
298
299
300
301
302
...
»

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

Brand: D-Link Pages: 12

SISPM1040-582-LRT

Brand: Lantronix Pages: 2

Brand: Lantronix Pages: 7

Brand: Analog Devices Pages: 76

IAR KickStart Kit TWR-K60N512-IAR

Brand: IAR SYSTEMS Pages: 8

Brand: Grizzly Pages: 9

ST62GP-EMU2 HDS2 Series

Brand: STMicroelectronics Pages: 58

Brand: Buffalo Pages: 2

Brand: Daedalon Pages: 6

Optane Persistent Memory 200 Series

Brand: Supermicro Pages: 54

Brand: MEDIATEK Pages: 166

Power System H924

Brand: IBM Pages: 48

Brand: IEI Technology Pages: 2

Brand: Xantech Pages: 5

Brand: Lattice Semiconductor Pages: 43

ACCULINK 3161 CSU

Brand: Paradyne Pages: 19

Brand: MA lighting Pages: 49

Brand: Omron Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands