Schweitzer Engineering SEL-2032 Instruction Manual Download Page 149 | Manualshive

Page: 149 / 354

background image

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Section 7

Settings

Introduction

This section provides detailed information about the commands used to
configure and control the SEL-2032 Communications Processor and explains
how you should respond to the SEL-2032 settings prompts. You can also use
this section as a reference to SEL-2032 settings when using the SEL-5020
Settings Assistant software. At the end of this section is a set of tables that list
all settings in the SEL-2032.

SET Commands

Use the

SET

command variations to configure the SEL-2032. These

commands correspond to the different classes of settings shown in

also shows how the

SET

commands relate to specific ports.

The SEL-2032 checks each entry to ensure that it is a valid choice. If it is not,
an “Out of Range” message is generated, and the SEL-2032 prompts for the
same setting again.

When you finish a setting, it is not necessary to scroll through the remaining
settings. Type

Y <Enter>

to approve the new settings or

N <Enter>

to abort

setting changes. If you type

Y <Enter>

and have a setting violation, an error

message is displayed, and the settings prompt moves to the first setting that
affects the failure. If settings are acceptable, the SEL-2032 saves them. While
the active settings are updated, the SEL-2032 port being modified is disabled
and the SALARM bit asserts for one second. In an SEL-2032, SALARM is
assigned to ALARM by default, so the alarm contact will close for one second
unless the ALARM setting has been modified.

When the settings change on a port, that port is reset. If you change the
settings on the current port, the settings become effective after being accepted.
If you change the baud rate, you will have to change the baud rate on your
terminal to match in order to resume communicating with the SEL-2032. You
may not change the settings on a port that is currently communicating
transparently with another port. Also, only one setting session is permitted at
one time; you will receive a message that the

SET

command is not available if

someone else is using one of the

SET

commands at the time you send a

SET

command.

Use the

COPY

or

SWAP

commands to copy and move settings between

ports. Always use the

SHOWSET

command on ports you copied or swapped

settings on to verify that all port references and messages are correct.

Courtesy of NationalSwitchgear.com

«
...
147
148
149
150
151
...
»

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

Brand: 3Com Pages: 8

Brand: Fostex Pages: 20

kontron KBox E-420-R1K/V1K

Brand: S&T Pages: 82

SABVISION NVR32

Brand: SAB Pages: 29

Brand: Kramer Pages: 2

4 Channel Input Buffer Board SDAIBB

Brand: B&B Electronics Pages: 22

Brand: ZyXEL Communications Pages: 3

Brand: Gearlinx Pages: 23

Brand: Accusys Pages: 34

Brand: IEI Technology Pages: 136

Brand: ICS ELECTRONICS Pages: 4

cPCIS-1100 Series

Brand: ADLINK Technology Pages: 48

Brand: Holtek Pages: 280

Brand: Hologic Pages: 256

Modular Fast Fiber Switch Converter MT-RJ

Brand: Lindy Pages: 3

Brand: protech Pages: 84

Suppression Inductors LFZ24H

Brand: Delta Electronics Pages: 1

Brand: Compaq Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands