Schweitzer Engineering SEL-2032 Instruction Manual Download Page 75

Page: 75 / 354

3.5

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Job Done Examples

Example 2: Using the SEL-2032 as a Port Switch

Step 2. Connect the IRIG-B time source to the SEL-2032 IRIG-B

input. (You need to know if the time source has a modulated or
demodulated IRIG-B signal. Set IRIG setting accordingly.)

NOTE

: You do not need to modify the

baud rate of Port 2 at the relay; the
SEL-2032 will match the baud rate
during auto-configuration.

Step 3. Connect the modem to Port 9 using cable SEL-C226,

and

connect a telephone line to the phone line connector on the
modem.

Step 4. Connect the serial port on your computer to Port F on the

SEL-2032 with an SEL C234A cable.

Set the SEL-2032

Step 1. Issue the

ACCESS

and

2ACCESS

commands and associated

passwords to go to Access Level 2.

Step 2. Use

SET P F

to set Port F parameters.

Step 3. Set Port 1 configuration communications options using the

SET P 1

command.

Step 4. Use

SET A 1

to define a timed trigger condition in the form of

(Thh:mm:ss) to send a date message at a specific time once
each day to the relay connected to Port 1.

Step 5. Use the

COPY 1 ALL

command to copy Port 1 settings to the

other ports (2, 3, 4, 5, 6, and 7) with devices attached.

Step 6. Use

SET P 9

to set Port 9 as a modem port.

Verify and Test All Communication Paths

Step 1. Use the

STATUS

command to check that the IRIG-B signal is

present and devices are connected to ports as expected.

Step 2. Check transparent communication with each port.

➢

Use the

PORT

command to enter transparent

communication with Port

, where

is any port number

(1–16).

➢

Use

<Ctrl+D>

to end transparent communication.

Step 3. Check that all SEL relays are receiving the proper IRIG-B

signal from the SEL-2032, that all relays have their Port 2 set to
issue auto-messages, and that the relay Port 2 time-out is OFF.

➢

Enter Transparent Communication with each port,
Access Level 1, and issue the

IRIG

command.

➢

Issue the

SHO

command to check the relay’s AUTO

and TIME settings.

➢

Exit transparent communication using the default
disconnect sequence,

<Ctrl+D>

Step 4. Check that the SEL-2032 issues the correct date code to each

relay. Change the relay date to the wrong year; use the

TOGGLE

command to issue the SEL-2032 date message.

Step 5. Check modem communication.

➢

Have someone call; the SEL-2032 modem should
answer by the fourth ring.

➢

The remote caller can enter transparent communication,
and you can watch the communication using front-
panel LEDs and the

STATUS

command.

Courtesy of NationalSwitchgear.com

Summary of Contents for SEL-2032



































































































































































































































































































































































Search results

Summary of Contents for SEL-2032

Reviews:

Related manuals for SEL-2032

Brands by name

Popular brands

Schweitzer Engineering SEL-2032, Instruction Manual

Search results

Summary of Contents for SEL-2032

Reviews:

Related manuals for SEL-2032

Brands by name

Popular brands