Schweitzer Engineering SEL-2032 Instruction Manual Download Page 202

Page: 202 / 354

SEL-2032

Communications Processor

Instruction Manual

Date Code 20120126

Settings Sheets

SEL-2701, SET P, and SET A

Date: ________________________________

Approved by: _________________________

SEL-2032 S/N: _______________________

DNPUP02

UDP Response Port Number for Master 2 (1–65534, REQ)

____________________

UNSL02

Enable Unsolicited Reporting for Master 2 (Y,N)

____________________

PUNSL02

Enable Unsolicited Reporting at Power up for Master 2 (Y,N)

____________________

DNPMP02

CUSTOM Mode: DNP3 map associated with Master 2 (1–5)

____________________

DNPCL02

Enable Controls for Master 2 (Y,N)

____________________

RPADR03

DNP3 Address for Master 3 (0–65519)

____________________

DNPIP03

IP Address for Master 3 (www.xxx.yyy.zzz)

____________________

DNPTR03

Transport Protocol for Master 3 (UDP, TCP)

____________________

DNPUP03

UDP Response Port Number for Master 3 (1–65534, REQ)

____________________

UNSL03

Enable Unsolicited Reporting for Master 3 (Y,N)

____________________

PUNSL03

Enable Unsolicited Reporting at Power up for Master 3 (Y,N)

____________________

DNPMP03

CUSTOM Mode: DNP3 map associated with Master 3 (1–5)

____________________

DNPCL03

Enable Controls for Master 3 (Y,N)

____________________

RPADR04

DNP3 Address for Master 4 (0–65519)

____________________

DNPIP04

IP Address for Master 4 (www.xxx.yyy.zzz)

____________________

DNPTR04

Transport Protocol for Master 4 (UDP, TCP)

____________________

DNPUP04

UDP Response Port Number for Master 4 (1–65534, REQ)

____________________

UNSL04

Enable Unsolicited Reporting for Master 4 (Y,N)

____________________

PUNSL04

Enable Unsolicited Reporting at Power up for Master 4 (Y,N)

____________________

DNPMP04

CUSTOM Mode: DNP3 map associated with Master 4 (1–5)

____________________

DNPCL04

Enable Controls for Master 4 (Y,N)

____________________

RPADR05

DNP3 Address for Master 5 (0–65519)

____________________

DNPIP05

IP Address for Master 5 (www.xxx.yyy.zzz)

____________________

DNPTR05

Transport Protocol for Master 5 (UDP, TCP)

____________________

DNPUP05

UDP Response Port Number for Master 5 (1–65534, REQ)

____________________

UNSL05

Enable Unsolicited Reporting for Master 5 (Y,N)

____________________

PUNSL05

Enable Unsolicited Reporting at Power up for Master 5 (Y,N)

____________________

DNPMP05

CUSTOM Mode: DNP3 map associated with Master 5 (1–5)

____________________

DNPCL05

Enable Controls for Master 5 (Y,N)

____________________

RPADR06

DNP3 Address for Master 6 (0–65519)

____________________

DNPIP06

IP Address for Master 6 (www.xxx.yyy.zzz)

____________________

DNPTR06

Transport Protocol for Master 6 (UDP, TCP)

____________________

DNPUP06

UDP Response Port Number for Master 6 (1–65534, REQ)

____________________

UNSL06

Enable Unsolicited Reporting for Master 6 (Y,N)

____________________

PUNSL06

Enable Unsolicited Reporting at Power up for Master 6 (Y,N)

____________________

DNPCL06

Enable Controls for Master 4 (Y,N)

____________________

RPADR07

DNP3 Address for Master 7 (0–65519)

____________________

DNPIP07

IP Address for Master 7 (www.xxx.yyy.zzz)

____________________

DNPTR07

Transport Protocol for Master 7 (UDP, TCP)

____________________

DNPUP07

UDP Response Port Number for Master 7 (1–65534, REQ)

____________________

UNSL07

Enable Unsolicited Reporting for Master 7 (Y,N)

____________________

Port ( 17 / 18 )

Courtesy of NationalSwitchgear.com

Summary of Contents for SEL-2032



































































































































































































































































































































































Search results

Summary of Contents for SEL-2032

Reviews:

Related manuals for SEL-2032

Brands by name

Popular brands

Schweitzer Engineering SEL-2032, Instruction Manual

Search results

Summary of Contents for SEL-2032

Reviews:

Related manuals for SEL-2032

Brands by name

Popular brands