Schweitzer Engineering SEL-2032 Instruction Manual Download Page 17 | Manualshive

Page: 17 / 354

background image

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Section 1

Introduction and Specifications

Introduction

The SEL-2032 Communications Processor provides many special features
needed in today’s substations to communicate with a variety of
microprocessor-based devices. The SEL-2032 can function as a simple, but
intelligent, port switch; or it can provide sophisticated communication and
data handling capability required for advanced substation integration projects.
This section provides the following:

➤

Introduction to the SEL-2032 and information on features,
applications, and specifications.

➤

Introduction to the terminology, concepts, and operation of
integrated substations and communications processors.

Applications

The functions of the SEL-2032 make it extremely versatile and powerful. You
can combine basic functions of the SEL-2032 to meet the requirements of
your application. Often the cost of the SEL-2032 is justified based on a single
major function, and other features add additional value to your application.
Several of the most popular applications are listed below.

Substation
Integrator

The communication processing and database capability of the SEL-2032 are
designed to collect and store data from numerous devices, parse it into useful
pieces, and distribute just the needed data to other devices or systems. This is
the fundamental purpose of substation integration, making the SEL-2032 a
natural choice for this application. Its networking capabilities allow it to be the
communication network for small substation integration projects, or it can
serve as a subnetwork integrator with one or more ties to a larger substation
network.

SCADA and
HMI Interface

The SEL-2032 can be interfaced with a variety of devices, including RTUs
and HMIs. The SEL-2032 can serve as a data concentrator, to be polled by a
local RTU, or it can be connected to a dedicated SCADA communication
circuit and polled by a central device.

Courtesy of NationalSwitchgear.com

«
...
15
16
17
18
19
...
»

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

Brand: Cabletron Systems Pages: 21

DR-4100P Series

Brand: Idis Pages: 30

Brand: TC Electronic Pages: 55

Emulator MCU Board for 38D5 Group M38D59T-RLFS

Brand: Renesas Pages: 4

Brand: UfiSpace Pages: 35

Brand: Point of View Pages: 13

Brand: Lutron Electronics Pages: 4

Brand: ZALMAN Pages: 8

Brand: XtendLan Pages: 21

Brand: Ariesys Pages: 10

Brand: PairGain Pages: 80

Brand: Quadram Pages: 21

DUAL Nx56/64 1200142L1#

Brand: ADTRAN Pages: 48

Brand: FOR-A Pages: 37

Brand: RAK Pages: 14

Brand: Classe Audio Pages: 70

Brand: ICP DAS USA Pages: 26

Brand: Tachosys Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands