Raritan PX-1000 Series User Manual Download Page 95

Page: 95 / 442

Chapter 5: Using the Web Interface

Browser-Defined Shortcut Menu

A shortcut menu, which is built in the web browser, may appear when
right-clicking anywhere in the Dominion PX web interface.

The shortcut menu functions are defined by the browser. For example, the
Back command on the Internet Explorer

(IE) shortcut menu works the

same as the Back button in the IE browser. Both of these functions take
you to the previous page.

For information on each shortcut menu command or item, see the online
help or documentation accompanying your web browser.

Below is the illustration of the IE browser's shortcut menu. Available menu
commands or items may slightly differ based on your web browser
version.

Summary of Contents for PX-1000 Series


























































































































































































































































































































































































































































Search results

Summary of Contents for PX-1000 Series

Reviews:

Related manuals for PX-1000 Series

Brands by name

Popular brands

Raritan PX-1000 Series, User Manual

Search results

Summary of Contents for PX-1000 Series

Reviews:

Related manuals for PX-1000 Series

Brands by name

Popular brands