manualshive.com logo in svg

Raritan PX-1000 Series, User Manual

The Raritan PX-1000 Series is a cutting-edge power distribution unit designed for seamless power management in data centers. For easy setup and operation, a comprehensive user manual is available to download for free from manualshive.com. This manual provides detailed instructions and troubleshooting tips to maximize the product's efficiency and performance.

Share
Download
background image

Chapter 3: Installation and Configuration 
 

44

 

 

Note: Each tag pot on the blade extension strip is labeled a number, which 
is displayed as the slot number in the Dominion PX's web interface. 

 

To install a blade extension strip: 

1.  Connect the tag connector cable to the blade extension strip. 

  Plug the cable's connector into the socket at either end of the 

blade extension strip. 

 

2.  Move the blade extension strip toward the bottom of the blade chassis 

until its mylar section is fully under the chassis, and verify that the 
blade extension strip does not fall off easily. If necessary, you may use 
the adhesive tape in the back of the mylar section to help fix the strip in 
place. 

 

 

3.  Connect one end of an asset tag to a blade server and connect the 

other end to the blade extension strip. 

a.  Affix the adhesive part of the asset tag to one side of a blade 

server through the tag's tape. 

Summary of Contents for PX-1000 Series



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PX-1000 Series

OBR PCM2 Installation And User Manual preview
PCM2
Brand: OBR Pages: 92
Ground Zero GZ PROtect Owner'S Manual preview
GZ PROtect
Brand: Ground Zero Pages: 4
Eaton SPD120480D3M Instruction Manual preview
SPD120480D3M
Brand: Eaton Pages: 14
GE SPM Series Instruction Manual preview
SPM Series
Brand: GE Pages: 126
Spectrum Brands 72A-190BQREM Series Installation And Operation Manual preview
72A-190BQREM Series
Brand: Spectrum Brands Pages: 26
Peak PKC0M04 Owner'S Manual preview
PKC0M04
Brand: Peak Pages: 14
nVent SCHROFF RP 2319 Quick Start Manual preview
RP 2319
Brand: nVent SCHROFF Pages: 3
nVent SCHROFF RackPower EP01024-0013 Assembly Diagram preview
RackPower EP01024-0013
Brand: nVent SCHROFF Pages: 3
Deif GPU 300 Manuallines preview
GPU 300
Brand: Deif Pages: 36
Tripp Lite SUDC Series Sequence Of Operation preview
SUDC Series
Brand: Tripp Lite Pages: 2

Brands by name

Popular brands

Load more brands