Raritan PX-1000 Series User Manual Download Page 252

Page: 252 / 442

Chapter 7: Using the Command Line Interface

237

Outlet Information

This command syntax shows the outlet information.

show outlets <n>

To show detailed information, add the parameter "details" to the end of the
command.

show outlets <n>

details

Variables:



<n> is one of the options:

all

, or a number.

Option

Description

all

Displays the information for all outlets.

Tip: You can also type the command without adding
this option "all" to get the same data.

A specific outlet
number

Displays the information for the specified outlet
only.

Displayed information:



Without the parameter "details," only the outlet name is displayed. For
PX-2000 series, the outlet state is also displayed.



With the parameter "details," more outlet information is displayed in
addition to the outlet name, such as the outlet rating.

Summary of Contents for PX-1000 Series


























































































































































































































































































































































































































































Search results

Summary of Contents for PX-1000 Series

Reviews:

Related manuals for PX-1000 Series

Brands by name

Popular brands

Raritan PX-1000 Series, User Manual

Search results

Summary of Contents for PX-1000 Series

Reviews:

Related manuals for PX-1000 Series

Brands by name

Popular brands