manualshive.com logo in svg

Pitney Bowes Relay 5000, Operator'S Manual, Page: 99 / 202

Share
Download
Pitney Bowes Relay 5000 Operator'S Manual Download Page 99

SV63136 Rev. A  

5-3

Troubleshooting • 5 

Adjusting 

Screen 

Brightness and 

Contrast

Follow the steps below to adjust the contrast and/or brightness of the dis-

play screen:
1.  From the Home screen, select "Menu".
2.  From the Menu screen, select "Tools".
3.  From the Tools screen, select "Configure System".
4.  From the Configure System screen, select "Set Brightness/Contrast".
5.  From the Set Brightness/Contrast screen:

•  Press the UP/DOWN arrow key(s) to increase/decrease screen 

brightness.

•  Press the LEFT/RIGHT arrow key(s) to decrease/increase screen 

contrast.

•  To return to the default settings, select "Restore Defaults".

6.  When you are done:

•  Press "Finished" to back through the configure system screens and 

return to the Home screen. Your settings will be saved.

 OR
•  Press HOME to save your adjustments and return directly to the 

Home screen.

Set Brightness/Contrast Screen

Set Brightness/Contrast

Job:  123

Press  

  to adjust Brightness. 

Press       to adjust Contrast.

100%

0%

100%

0%

Restore Defaults

Finished

Summary of Contents for Relay 5000











































































































































































































Reviews:

No comments