manualshive.com logo in svg

Pitney Bowes Relay 5000, Operator'S Manual, Page: 59 / 202

Share
Download
Pitney Bowes Relay 5000 Operator'S Manual Download Page 59

SV63136 Rev. A  

3-15

Basic Operation • 3 

Adjusting the HCEF Wedge

1.  Insert an envelope into the HCEF with the bottom edge of the envelope 

against the center guide, in line with the two screws. The top edge of the 

envelope (edge with flap) should point towards the wedge.

NOTE:

  Ensure the envelope is centered, 

not angled

, on the center guide 

to obtain correct positioning. If the position of the envelope is incorrect, the 

separator gap adjustment will be incorrect as well. 

2.  Push up and release the blue wedge locking lever.
3.  Slide the wedge toward the envelope, until the top edge of the envelope 

fits into the center slot of the wedge.

Loading 

the HCEF 

(continued)

Figure 3.7.1:  Adjusting the Wedge Position

Wedge 

Locking 

Lever

Wedge

Center Guide

Summary of Contents for Relay 5000











































































































































































































Reviews:

No comments