Pitney Bowes Relay 5000 Operator'S Manual Download Page 110

Page: 110 / 202

5-14

SV63136 Rev. A

5 • Troubleshooting

Table 5-6 Insertion Area/Envelope Flapper Area Problems,

continued

Problem

Cause

Action

•

Contents of insertion

pack are catching on

side seam inside of

envelope.

•

Contents of insertion

pack are thick and

difficult to insert into

smaller envelopes.

Adjust the Aligner custom settings:

NOTE:

If the contents of the insertion pack are thick, and you

are having trouble inserting the pack into a small envelope, be

sure to set the "Envelope Width" and "Widest Enclosure Width"

to the exact dimensions of the insertion pack.
1.  From the Home screen, select "Menu", then "Jobs".
2.  Select "Edit Current Job", "Edit Job Settings", "Advanced".
3.  Select "Aligner", then "On with Custom Settings". The

Customer Aligner Settings screen displays.

4. Select "Envelope Width". Use the UP/DOWN arrow keys

to increase or decrease the measurement, as necessary.

Select "Accept" when done.

5. Select "Widest Enclosure Width". Use the UP/DOWN

arrow keys to increase or decrease the measurement, as

necessary. Select "Accept" when done.

6. Select "Accept" on the Custom Aligner Settings screen

once the necessary adjustments have been made

Summary of Contents for Relay 5000










































































































































































































Search results

Summary of Contents for Relay 5000

Reviews:

Pitney Bowes Relay 5000, Operator'S Manual, Page: 110 / 202

Search results

Summary of Contents for Relay 5000

Reviews: