Pitney Bowes Relay 5000 Operator'S Manual Download Page 197

Page: 197 / 202

SV63136 Rev. A

A-5

Glossary • A

Icon Glossary

Envelope Icons

Tower Feeder
Orientation:

flap side down,

flap first

HCEF*
Orientation:

flap side down,

flap last.

Non-Window Letter

Envelope
Window Standard Flap

Envelope
Window Forward Flap Letter

Envelope
Window Bottom Flap

Letter Envelope

Non-Window Flat

Envelope

N/A

Window Standard Flap Flat

Envelope

N/A

Window Forward Flap Flat

Envelope

N/A

Window Bottom Flap Flat

Envelope

N/A

*High Capacity Envelope Feeder

The tables in this section provide descriptions of the various icons you will

see on the display screen.

Dark lines within an icon represent features

you can plainly see.

Where applicable, the darkest edge of an icon

is the edge that feeds first into the system.

Light grey lines

within an icon

represent features

that you cannot

be see.

(For example,

the flap on the

reverse side of an

envelope.)

Summary of Contents for Relay 5000










































































































































































































Search results

Summary of Contents for Relay 5000

Reviews:

Pitney Bowes Relay 5000, Operator'S Manual, Page: 197 / 202

Search results

Summary of Contents for Relay 5000

Reviews: