manualshive.com logo in svg

Pitney Bowes Relay 5000, Operator'S Manual, Page: 52 / 202

Share
Download
Pitney Bowes Relay 5000 Operator'S Manual Download Page 52

3-8

SV63136  Rev.  A  

3 • Basic Operation 

3.  Slide the tray into the tray mounts until you feel the Tray seat into place.

NOTE:

  The tray is seated properly when the notch on the bottom of each 

side of the tray is seated in the groove on each of the tray mounts.

4.  Pull straight back on the tray slightly, and at the angle at which the Tray 

sits, to ensure it is securely attached. If it isn’t, repeat the procedure until 

the tray seats properly and securely.

Figure 3.1.2: Check Tray Seating

Figure 3.1.2:  Tray Seated Properly in Tray Mount 

(bottom view)

Notch on Tray

Groove on 

tray mount

Removing Trays 

from the Feeder 

Tower

The procedure for removing a sheet or insert tray consists of the following: 
1.  Grasp the open end of the tray and lift up.
2.  Slide the tray out until it clears the grooves in the tray mount.

Summary of Contents for Relay 5000











































































































































































































Reviews:

No comments