Pitney Bowes Relay 5000 Operator'S Manual Download Page 138

Page: 138 / 202

7-6

SV63136 Rev. A

7 • Add-On Modules

If the sheet width is different from the sheet width used in the previous job,

you need to adjust the HCSF guides for the new job.

IMPORTANT:

Make sure you have enabled the High Capacity Sheet Feeder

Trays before performing this adjustment. Refer to

Enabling and Disabling the High

Capacity Sheet Feeder (HCSF)

Chapter 4

for more information.

1. From the Home screen, select "Loading Instructions", then "Pre-Run

Adjustments", and finally, "HCSF Guide Settings".

2.  Select the Feeder that you will be setting up.
3.  Press TRIAL PIECE.
4.  Open the front and top covers of the enabled HCSF accumulation area.

Adjusting the

HCSF Guides

Figure 7.6: HCSF Front and Top Covers Open

Figure 7.5: HCSF Front and Top Covers

HCSF Top Cover

HCSF Front Cover

Summary of Contents for Relay 5000










































































































































































































Search results

Summary of Contents for Relay 5000

Reviews:

Pitney Bowes Relay 5000, Operator'S Manual, Page: 138 / 202

Search results

Summary of Contents for Relay 5000

Reviews: