Pitney Bowes Relay 5000 Operator'S Manual Download Page 200

Page: 200 / 202

A-8

SV63136 Rev. A

A • Glossary

Icon Glossary

(continued)

Feeder Assignment Icons

Feeder assignment is indicated by a letter in a grey square to the right of the

job item icon in the Mail Piece Icon Tree. The letter that appears in the blue

square will vary, depending upon the assigned feeder.

•

Single Feeder Assignment

is indicated by one grey square.

•

Linked Feeder Assignment

is indicated by two grey squares.

NOTE:

The table below provides a list of all possible Feeder assignments. The

Feeders available to you will vary, depending upon your system configuration.

Feeder Letter

Location

Position

Feeder Tower

Bottom left feeder

Feeder Tower

Bottom right feeder

Feeder Tower

Top left feeder

Feeder Tower

Top right feeder

High Capacity Envelope Feeder (HCEF)

N/A

High Capacity Sheet Feeder 1 (HCSF)

Bottom feeder

High Capacity Sheet Feeder 1 (HCSF)

Top feeder

High Capacity Sheet Feeder 2 (HCSF)

Bottom feeder

High Capacity Sheet Feeder 2 (HCSF)

Top feeder

Custom Feeder

N/A

Attached Printer

N/A

Other Icons

Error Icon

- appears in pop-up messages on display screen.

Indicates message is an error message.

Warning Icon

- appears in pop-up messages on display screen.

Indicates message is a warning message.

Seal On Icon

- appears in Mail Piece Icon Tree if sealing is on.

Safe Seal Icon

- appears in Mail Piece Icon Tree if safe seal is on.

Double Detect Icon

- appears in Mail Piece Icon Tree if double

detect is on.

Summary of Contents for Relay 5000










































































































































































































Search results

Summary of Contents for Relay 5000

Reviews:

Pitney Bowes Relay 5000, Operator'S Manual, Page: 200 / 202

Search results

Summary of Contents for Relay 5000

Reviews: