manualshive.com logo in svg

Pitney Bowes Relay 5000, Operator'S Manual, Page: 141 / 202

Share
Download
Pitney Bowes Relay 5000 Operator'S Manual Download Page 141

SV63136 Rev. A  

7-9

Add-On Modules • 7 

The Flats Sealer also contains an envelope edge marker. The envelope 

edge marker will apply a mark at least 0.5" (12.5 mm) in length along the 

edge of the envelope facing the operator. 
You can use edge mark can be used to indicate tray breaks, ZIP breaks, 

every 50th envelope, high value checks, etc. 

NOTE:

  The envelope edge mark is applied only to envelopes passing through the 

letter exit path.

Replacing the 

Envelope Edge 

Marker Roller

Follow the steps below to remove and replace the Envelope Edge Marker 

Roller.

NOTE: 

 Avoid touching the ink roller, as it is covered in ink.

1.  Open the Flats Sealer cover.
2.  Grasp the tab at the top of the old ink roller and lift to remove.
3.  Grasp the tab at  the top of the new ink roller and slide it onto the spin-

dle.

4.  Release the tab once the ink roller is seated firmly in place.
5.  Close the Flats Sealer cover.

Figure 7.9:  Flats Sealer Cover Open

Envelope Edge Marker Roller

Flat Envelope Exit

Letter Envelope Exit

Summary of Contents for Relay 5000











































































































































































































Reviews:

No comments