manualshive.com logo in svg

Pitney Bowes Relay 5000, Operator'S Manual, Page: 62 / 202

Share
Download
Pitney Bowes Relay 5000 Operator'S Manual Download Page 62

3-18

SV63136  Rev.  A  

3 • Basic Operation 

6.  Shingle a .7 to 2-inch  (20mm to 50mm) stack of envelopes. Place the 

envelopes into the HCEF flap side down, flap last.

7.  Finish loading a full stack of envelopes (up to 500 pieces), making 

sure that the envelopes contact the back of the side guides. It is not 

necessary to shingle the remaining envelopes.

NOTES:

  

•  If an HCSF or attached printer is present, you may need to adjust guides 

to ensure sheets feed correctly. Refer to 

Adjusting the HCSF Guides

 or 

Adjusting the Printer Interface Guides

 in 

Chapter 7

 of this guide for more 

information.

•  If you are using scanning, you may need to adjust the scan head to ensure 

the bar code or OMR mark is read. Refer to 

Adjusting the Scan Heads

 in 

Chapter 8

 of this guide for more information. 

3.  Place the envelope, bottom edge 

first, into the separator so the top 

edge (flap crease) lines up with the 

edge of the tab on the Wedge.

NOTE:

  The edge of the tab is indi-

cated by two arrows.

4.  Lower the separator completely, then 

push down on the separator gap le-

ver to lock it into place.

5.  Pull the envelope out from the HCEF.

Figure 3.8.3:  Envelopes Lined Up with Tab on Wedge.

Loading 

the HCEF 

(continued)

Summary of Contents for Relay 5000











































































































































































































Reviews:

No comments