manualshive.com logo in svg

Pitney Bowes Relay 5000, Operator'S Manual, Page: 47 / 202

Share
Download
Pitney Bowes Relay 5000 Operator'S Manual Download Page 47

SV63136 Rev. A  

3-3

Basic Operation • 3 

Powering Up

WARNING!

 Read the safety information in 

Chapter 1

 before con-

necting the system to power.

To connect the system to power:
1.  Connect the power cord to the socket on the back of the inserter.
2.  Plug the power cord into a suitable power outlet. Verify the power outlet 

is near the inserter and is easily accessible.

These instructions explain how to:
•  Properly power up the inserting system, and
•  Select a job.

Connecting to 

Power

Press the ON/OFF switch (located below the control panel) to start the pow-

er up process.

NOTE: 

 If a High Capacity Sheet Feeder (HCSF) is present, power on before you 

power on the base. 

The system will automatically conduct a number of checks to verify the op-

erational integrity of the system. If any problems are detected, the system 

will display information directing you to a solution to the problem.

NOTE: 

 When power cycling the system, be sure to power cycle any optional add-

on equipment as well. 

Summary of Contents for Relay 5000











































































































































































































Reviews:

No comments