Pitney Bowes Relay 5000 Operator'S Manual Download Page 157

Page: 157 / 202

SV63136 Rev. A

8-11

Scanning • 8

Most Barcode readers do not require barcode internal data encoding to be

specified in order to read the barcode. However, Data Matrix barcodes do

support internal error detection and correction. The level of error detection

and correction is known as the ECC level.
The use of ECC allows for codes to be partially damaged but remain read-

able. The amount of error correction built into a Data Matrix barcode does

not limit the data capacity of the barcode.
The HCSF supports Data Matrix barcodes for all ECC levels.
•

New Applications

ECC 200 (the current industry standard)

•

Legacy Applications

ECC 140

ECC 130

ECC 120

ECC 100

ECC 080

ECC 050

ECC 000

Supported ECC

(Error Correction

Code) Levels

Summary of Contents for Relay 5000










































































































































































































Search results

Summary of Contents for Relay 5000

Reviews:

Pitney Bowes Relay 5000, Operator'S Manual, Page: 157 / 202

Search results

Summary of Contents for Relay 5000

Reviews: