Pitney Bowes Relay 5000 Operator'S Manual Download Page 42

Page: 42 / 202

2-24

SV63136 Rev. A

2 • Meet the Inserting System

To open the Main Transport Deck Cover:

1. Place your fingers into the slot on the top of the cover.
2. Pull down gently. A security tie keeps the cover within the recommended

range of movement.

IMPORTANT:

Do NOT lean on the open cover.

To open the Tower Base Cover:

1. Open the main transport deck cover.
2. Pull down on the tower base cover handle.

The tower base cover interlocks with the main transport deck cover. This

means that you cannot open the tower base cover unless you open the

main transport deck cover first.

Opening the

Covers

Closing the

Covers

To close the lower tower and/or the main transport deck cover, push the

cover up until it is seated in place on the system deck.

CAUTION

Moving mechanism can result in

personal injury.

Keep hands, long hair, ties,

jewelry and loose clothing away

from moving parts.

Summary of Contents for Relay 5000










































































































































































































Search results

Summary of Contents for Relay 5000

Reviews:

Pitney Bowes Relay 5000, Operator'S Manual, Page: 42 / 202

Search results

Summary of Contents for Relay 5000

Reviews: