manualshive.com logo in svg

Oracle Netra SPARC S7-2, Service Manual, Page: 176 / 258

Share
Download
Oracle Netra SPARC S7-2 Service Manual Download Page 176

Install a PCIe Card

See 

“Install a PCIe Card” on page 176

.

8.

Power on the server.

See 

“Returning a Server to Operation” on page 235

.

Related Information

■

“Locate a Faulty PCIe Card” on page 172

■

“Install a PCIe Card” on page 176

■

“Preparing for Service” on page 43

■

“Returning a Server to Operation” on page 235

Install a PCIe Card

Installing a PCIe card is a cold-service operation. You must power off the server before

installing the PCIe card.

Note - 

This procedure is the same for installing a PCIe filler.

1.

If you are installing additional cards, review this information and complete these

prerequisites in this order.

See:

■

“PCIe Card Configurations” on page 170

■

“Preparing for Service” on page 43

■

“Remove a PCIe Card” on page 174

Remove the filler.

2.

If you are replacing a faulty card and have not removed the faulty card, remove it

and return to this procedure.

See 

“Remove a PCIe Card” on page 174

.

3.

If not already done, prepare for service.

See 

“Preparing for Service” on page 43

.

4.

Position the PCIe card at the slot where it will be installed.

5.

Press the PCIe card into the socket.

176

Netra SPARC S7-2 Server Service Manual • February 2017

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Reviews:

No comments