Oracle Netra SPARC S7-2 Service Manual Download

Page: 88 / 258

Locate a Faulty Drive

Volumes
Expanders
Properties:
health = OK
health_details = -
...
->

If the

health_details

property identifies a faulty drive, replace it. See

“Remove a SAS

Drive” on page 89

Check the health of the individual drives.

show /System/Storage/Disks/Disk_

/System/Storage/Disks/Disk_0
Targets:
Properties:
health = OK
health_details = -
...
->

where

is the number of the drive, from

If the

health_details

property identifies the drive as faulty, replace it. See

“Remove a SAS

Drive” on page 89

Verify that a drive is faulty.

If a drive is faulty, you will see

/SYS/DBP/HDD

under the

Value

heading, where

For example, type:

show faulty

Target | Property | Value
--------------------+------------------------+-------------------------------
/SP/faultmgmt/0 | fru | /SYS/DBP/HDD0
...
->

If a drive is faulty, replace it.
See

“Remove a SAS Drive” on page 89

If a FRU value different from

/SYS/DBP/HDD

is displayed, see

“Component Service Task

Reference” on page 47

to identify which component is faulty.

Use the Oracle ILOM

faultmgmt

shell to identify the faulty component.

See

“Identify Faulted Components” on page 27

Netra SPARC S7-2 Server Service Manual • February 2017

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands

Oracle Netra SPARC S7-2, Service Manual

Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands