manualshive.com logo in svg

Oracle Netra SPARC S7-2, Service Manual, Page: 232 / 258

Share
Download
Oracle Netra SPARC S7-2 Service Manual Download Page 232

Install the Motherboard

3.

Tilt the motherboard to clear the cable tie mounted on the left.

4.

Lower the motherboard onto the bottom alignment pins.

5.

Slowly slide the motherboard until it drops, engaging the bottom alignment pins.

6.

Carefully insert the LED into the hole at the rear of the chassis.

7.

Continue to slide the motherboard forward until it seats.

The rear of the motherboard must be flush with the rear of the server. Additionally, the four

holes in the motherboard must align with the four holes in the bus bars.

8.

Tighten the captive screw.

9.

Install and tighten the four bus bar screws.

10.

Install the right thumb screw bracket.

232

Netra SPARC S7-2 Server Service Manual • February 2017

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Reviews:

No comments