Oracle Netra SPARC S7-2 Service Manual Download Page 154

Page: 154 / 258

Remove a Fan Module

On the fan module to be replaced, pull the green band straight up and lift the fan

module out of the server.

Set the fan module aside.

Repeat from

Step 3

for any additional fan modules to be removed.

Consider your next step.

■

If you are replacing a faulty fan module, install the new fan module.

See

“Install a Fan Module” on page 155

■

If you removed a fan module as part of another component's removal or

installation procedure, return to that procedure.

See

“Component Service Task Reference” on page 47

for assistance.

Related Information

■

“Locate a Faulty Fan Module” on page 152

■

“Install a Fan Module” on page 155

■

“Preparing for Service” on page 43

■

“Returning a Server to Operation” on page 235

154

Netra SPARC S7-2 Server Service Manual • February 2017

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Oracle Netra SPARC S7-2, Service Manual, Page: 154 / 258

Search results

Summary of Contents for Netra SPARC S7-2

Reviews: