manualshive.com logo in svg

Oracle Netra SPARC S7-2, Service Manual, Page: 223 / 258

Share
Download
Oracle Netra SPARC S7-2 Service Manual Download Page 223

Install the LED Board and Cable

7.

Connect the LED cable to the LED assembly.

8.

If you installed the LED board as part of another component's removal or

installation procedure, return to that procedure.

See 

“Component Service Task Reference” on page 47

 for assistance.

9.

Review this information and complete these prerequisites in this order.

See:

■

“Install the Air Duct” on page 236

■

“Install the PSU Duct” on page 240

■

“Secure the Drive Cage” on page 241

■

“Install the Filter” on page 82

10.

Complete these postrequisites in this order to finish the installation procedure.

See:

■

“Returning a Server to Operation” on page 235

■

“Verify the LED Board” on page 224

Related Information

■

“Remove the LED Board and Cable” on page 218

Servicing the LED Board

223

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Reviews:

No comments