Oracle Netra SPARC S7-2 Service Manual Download Page 191

Page: 191 / 258

Install the Battery

Install the Battery

Installing the battery is a cold-service operation. You must power off the server before installing

the battery.

If you have not done so already, prepare for service and remove the battery.

See:

■

“Preparing for Service” on page 43

■

“Remove the Battery” on page 189

Press the battery into the receptacle until you hear a click.

The positive (+) side of the battery faces toward the PCIe card slots 1-4.

If you installed the battery as part of another component's removal or installation

procedure, return to that procedure.

See

“Component Service Task Reference” on page 47

for assistance.

Finish the installation procedure.

See

“Returning a Server to Operation” on page 235

Set the date and time on SP and Host OS.

Restore the Oracle ILOM variables.

See

http://docs.oracle.com/cd/E19860-01/E21549/z40015841018582.html#scrolltoc

Related Information

■

“Remove the Battery” on page 189

■

“Preparing for Service” on page 43

■

“Returning a Server to Operation” on page 235

Servicing the Battery

191

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Oracle Netra SPARC S7-2, Service Manual, Page: 191 / 258

Search results

Summary of Contents for Netra SPARC S7-2

Reviews: