manualshive.com logo in svg

Oracle Netra SPARC S7-2, Service Manual, Page: 104 / 258

Share
Download
Oracle Netra SPARC S7-2 Service Manual Download Page 104

Locate an eUSB Drive

Locate an eUSB Drive

From the OpenBoot PROM, type:

ok

probe-scsi-all

.../pci@300/pci@1/pci@0/pci@2/usb@0/[email protected]...
1112
...

Related Information

■

“Determine if an eUSB Drive is Faulty” on page 104

■

“Identifying Components” on page 13

■

“Install the eUSB Drive” on page 106

■

“Remove the eUSB Drive” on page 105

Determine if an eUSB Drive is Faulty

1.

Check to see if any Server Service Required LEDs are lit or flashing.

See 

“Front Panel Components (Service)” on page 17

 and 

“Interpreting LEDs” on page 30

.

2.

In Oracle ILOM, verify that the eUSB drive is recognized and check the

fault_state.

->

show/SYS/MB/EUSB_DISK/

./SYS/MB/EUSB_DISK
....Targets:
....Properties:
....type.=.Flash.Mini-Disk
....fault_state.=.OK
....clear_fault_action.=.none)
....Commands:
....cd
....set
....show
...
->

3.

Use the Oracle ILOM 

faultmgmt

 shell or the 

fmadm faulty

 command to identify a

faulty component.

104

Netra SPARC S7-2 Server Service Manual • February 2017

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Reviews:

No comments