Oracle Netra SPARC S7-2 Service Manual Download Page 71

Page: 71 / 258

Rotate the Drive Cage to the Service Position

See

“Rotate the Drive Cage to the Service Position” on page 71

Related Information

■

“Remove the Top Cover” on page 67

■

“Install the Fan Tray” on page 244

■

“Rotate the Drive Cage to the Service Position” on page 71

Rotate the Drive Cage to the Service Position

Complete these prerequisites in this order.

“Remove the Top Cover” on page 67

“Remove a Fan Module” on page 153

Note -

Remove all fan modules.

“Remove the Fan Tray” on page 69

Disconnect the cables attached to the drive backplane, and the cable attached to

the USB board.

See

“Cable Configurations” on page 194

for location of cables.

Tip -

For easier removal, first press the cables in, then press the release tab, then pull the cables

out,

The cables are shown in the illustration in

“Cable Configurations” on page 194

Fully insert or remove any partially removed drives before continuing.

Preparing for Service

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Oracle Netra SPARC S7-2, Service Manual, Page: 71 / 258

Search results

Summary of Contents for Netra SPARC S7-2

Reviews: