manualshive.com logo in svg

Oracle Netra SPARC S7-2, Service Manual, Page: 198 / 258

Share
Download
Oracle Netra SPARC S7-2 Service Manual Download Page 198

Install the SAS Drive Signal Cable

Caution - 

Avoid hitting and lifting the MAC label nearby. If it is raised while routing the cable,

reseat it.

a.   

Open the clip, and pass the cable through at a 45-degree angle to get under

one tab.

b.   

Angle the cable the opposite direction, then insert it under the other tab.

c.   

Close the clip on the cable pass through.

d.   

Make sure the cables have enough slack so that they are not pulling on HBA

card.

Caution - 

The HBA card will bend if the cables are too tight.

e.   

Ensure that the cable pass through is seated all the way towards the HBA

card.

f.   

Make sure that the cable pass through remains seated on all four corners.

3.

Connect the cable to the HBA card in slot 7.

198

Netra SPARC S7-2 Server Service Manual • February 2017

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Reviews:

No comments