manualshive.com logo in svg

Oracle Netra SPARC S7-2, Service Manual, Page: 92 / 258

Share
Download
Oracle Netra SPARC S7-2 Service Manual Download Page 92

Install a SAS Drive

Related Information

■

“Locate a Faulty Drive” on page 87

■

“Install a SAS Drive” on page 92

■

“Preparing for Service” on page 43

■

“Returning a Server to Operation” on page 235

Install a SAS Drive

Installing a SAS drive is a hot-plug operation. You do not need to power off the server before

installing the drive. This procedure is the same for installing a drive filler.

1.

Consider your first step.

■

If you are replacing a drive, remove the faulty or obsolete drive first, then

return to this procedure, 

Step 3

.

See 

“Remove a SAS Drive” on page 89

.

■

If you are installing a new or an additional drive, go to 

Step 2

.

■

If you are installing a drive as part of another component's service

procedure, go to 

Step 3

.

2.

Review this information and complete these prerequisites in this order.

See:

■

“Preparing for Service” on page 43

■

“SAS Drive Configuration” on page 86

■

“Remove the Filter” on page 79

3.

Push the release button of the drive.

The release lever pops out.

92

Netra SPARC S7-2 Server Service Manual • February 2017

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Reviews:

No comments