manualshive.com logo in svg

Oracle Netra SPARC S7-2, Service Manual, Page: 132 / 258

Share
Download
Oracle Netra SPARC S7-2 Service Manual Download Page 132

Power Supply LEDs

Related Information

■

“Identifying Components” on page 13

■

“Detecting and Managing Faults” on page 25

■

“Component Service Task Reference” on page 47

■

“Preparing for Service” on page 43

■

“Returning a Server to Operation” on page 235

Power Supply LEDs

The status of each power supply is represented by two LEDs. These are located to the left of

the fan of each power supply. See 

“Rear Panel LEDs” on page 33

 and 

“Rear Panel Components

(Service)” on page 18

.

Icon

Location

Name

Color

State and Meaning

Top

AC or DC

Green

On

 – Input power present and good.

Off

 – Input power not present.

Top

Attention

Service Required

Amber

On

 – Normal fault detected.

Off

 – No faults detected.

Related Information

■

“Locate a Faulty Power Supply” on page 132

■

“Remove a Power Supply” on page 134

■

“Front Panel Components (Service)” on page 17

■

“Rear Panel Components (Service)” on page 18

Locate a Faulty Power Supply

You must determine which power supply is faulty before you replace it.

1.

Check to see if any System Service Required LEDs are lit or flashing.

See 

“Front Panel Components (Service)” on page 17

.

132

Netra SPARC S7-2 Server Service Manual • February 2017

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Reviews:

No comments