manualshive.com logo in svg

Oracle Netra SPARC S7-2, Service Manual, Page: 178 / 258

Share
Download
Oracle Netra SPARC S7-2 Service Manual Download Page 178

Verify a PCIe Card

->

where 

y

 is 

0

 to 

6

 for the slot numbers.

3.

Verify that the PCIe card is recognized.

-> 

show /System/PCI_Devices/Add-on

 /System/PCI_Devices/Add-on
  Targets:
   Device_

x

   Device_

y

...
->

where 

x

, 

y

, and so on are the slot numbers where PCIe cards are installed.

If the PCIe card is not recognized, check its installation.

4.

Verify that the PCIe card is identified.

-> 

show /System/PCI_Devices/Add-on/Device_

x

where 

x

 is the slot number where the PCIe card is installed.

5.

If a card is not recognized, try to locate it.

See 

“Locate a Faulty PCIe Card” on page 172

.

Related Information

■

“Install a PCIe Card” on page 176

■

“PCIe Card Configurations” on page 170

■

“Locate a Faulty PCIe Card” on page 172

178

Netra SPARC S7-2 Server Service Manual • February 2017

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Reviews:

No comments