Oracle Netra SPARC S7-2 Service Manual Download

Page: 32 / 258

Interpreting LEDs

No.

LED

Description

Service Required LED (amber)

Indicates that service is required.

The Oracle ILOM

show faulty

command provides details about any faults that cause

this indicator to light.

Under some fault conditions, individual component fault LEDs are turned on in

addition to the Service Required LED.

Locator LED and button (white)

The Locator LED can be turned on to identify a particular system. When on, the LED

blinks rapidly.

Pressing and holding the Locator button for 5 seconds initiates a test of all LEDs in the

LED assembly.

Hard drive status LEDs:

Indicates these conditions:

■

Off

– Drive is not ready or is faulty.

■

Steady on

–Drive is on and idle.

■

Fast blink

– Read or write activity is in progress.

■ Ready to Remove LED (top,

blue)

Indicates that the drive can be removed during a hot-plug operation.

■ Service Required LED (middle,

amber)

Indicates that the drive has experienced a fault condition.

■ OK/Activity LED (bottom,

green)

Indicates the drive's availability for use.

■

– Read or write activity is in progress.

■

Off

– Drive is idle and available for use.

Related Information

■

“Rear Panel LEDs” on page 33

■

“Checking for Faults” on page 25

■

“Performing Advanced Troubleshooting” on page 34

■

“Clear a Fault Manually” on page 40

Netra SPARC S7-2 Server Service Manual • February 2017

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands

Oracle Netra SPARC S7-2, Service Manual

Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands