Oracle Netra SPARC S7-2 Service Manual Download Page 94

Page: 94 / 258

Install a SAS Drive

Press the release lever fully closed with a click, securing the drive into the

server.

Repeat from

Step 3

through

Step 6

for any additional drives that you are

installing.

Consider your next step.

■

If you installed a new or replacement drive, go to

Step 9

■

If you installed a drive as part of another component's removal or

installation procedure, return to that procedure.

See

“Component Service Task Reference” on page 47

Rotate the air filter up until the latches click.

See

“Install the Filter” on page 82

10.

Complete these tasks to finish the service procedure.

See:

■

“Returning a Server to Operation” on page 235

■

“Verify a SAS Drive” on page 95

Netra SPARC S7-2 Server Service Manual • February 2017

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Oracle Netra SPARC S7-2, Service Manual, Page: 94 / 258

Search results

Summary of Contents for Netra SPARC S7-2

Reviews: