manualshive.com logo in svg

Oracle Netra SPARC S7-2, Service Manual, Page: 51 / 258

Share
Download
Oracle Netra SPARC S7-2 Service Manual Download Page 51

Power Off the Server (Power Button - Graceful)

See 

“Log In to Oracle ILOM (Service)” on page 26

.

Depending on the type of problem, you might want to view server status or log files. Also, you

might want to run diagnostics before you shut down the server. See 

“Detecting and Managing

Faults” on page 25

.

2.

Power off the server.

-> 

stop /System

Are you sure you want to stop /System (y/n)? 

y

Stopping /System
->

Note - 

You can use the Power button on the front of the server to initiate a graceful server

shutdown. See 

“Power Off the Server (Power Button - Graceful)” on page 51

. This button

is recessed to prevent accidental server power off.

Related Information

■

“Prepare to Power Off a Server” on page 50

■

“Disconnect Power Cords and Data Cables” on page 52

■

“Power On the Server (Oracle ILOM)” on page 249

■

“Power Off the Server (Power Button - Graceful)” on page 51

■

“Power Off the Server (Emergency Shutdown)” on page 52

Power Off the Server (Power Button - Graceful)

This procedure places a server in the power standby mode. In this mode, the Power OK LED

blinks rapidly.

Press and release the recessed Power button.

See 

“Front Panel Components (Service)” on page 17

.

Related Information

■

“Prepare to Power Off a Server” on page 50

■

“Disconnect Power Cords and Data Cables” on page 52

■

“Power On the Server (Power Button)” on page 250

■

“Front Panel Components (Service)” on page 17

■

“Power Off the Server (Oracle ILOM)” on page 50

Preparing for Service

51

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Reviews:

No comments