manualshive.com logo in svg

Oracle Netra SPARC S7-2, Service Manual, Page: 205 / 258

Share
Download
Oracle Netra SPARC S7-2 Service Manual Download Page 205

Remove the PDB Signal Cable

4.

Disconnect the cable from the PDB and the motherboard.

5.

Set the cable aside.

6.

Consider your next step.

■

If you are replacing a cable, install the new cable.

See 

“Install the PDB Signal Cable” on page 206

.

■

If you removed a cable as part of another component's removal or

installation procedure, return to that procedure.

See 

“Component Service Task Reference” on page 47

.

Related Information

■

“Install the PDB Signal Cable” on page 206

■

“Component Locations (Storage, Power, NVMe, and Fan Modules)” on page 14

■

“Component Locations (Motherboard, Memory, and PCIe Cards)” on page 16

■

“Preparing for Service” on page 43

■

“Returning a Server to Operation” on page 235

Servicing the Cables

205

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Reviews:

No comments