manualshive.com logo in svg

Oracle Netra SPARC S7-2, Service Manual, Page: 148 / 258

Share
Download
Oracle Netra SPARC S7-2 Service Manual Download Page 148

Install the PDB

7.

Reconnect the cable to the PDB.

8.

Install the fan tray bracket and fan tray.

See 

“Install the Fan Tray” on page 244

.

9.

Install the right thumb screw bracket.

10.

Connect the cables from the motherboard.

11.

Connect the LED assembly cable, and close the cable tie on the right side of the

chassis.

12.

If you installed the PDB as part of another component's removal or installation

procedure, return to that procedure.

See 

“Component Service Task Reference” on page 47

.

13.

Review this information and complete these prerequisites in this order.

See:

■

“Install the Internal HBA PCIe Card” on page 183

■

“Install a PCIe Card” on page 176

■

“Install the Air Duct” on page 236

■

“Install the PSU Duct” on page 240

148

Netra SPARC S7-2 Server Service Manual • February 2017

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Reviews:

No comments