Oracle Netra SPARC S7-2 Service Manual Download Page 103

Page: 103 / 258

Servicing the eUSB Drive

Caution -

These procedures require that you handle components that are sensitive to static

discharge. This sensitivity can cause the component to fail. To avoid damage, ensure that you

follow antistatic practices to

“Prevent ESD Damage” on page 55

Caution -

Ensure that all power is removed from the server before removing or installing an

eUSB drive, or damage to the drive might occur. You must disconnect all power cables from the

system before performing these procedures.

The eUSB drive provides USB 3.0 connectivity at the rear of the server. See

“Component

Locations (Storage, Power, NVMe, and Fan Modules)” on page 14

Description

Links

Replace a faulty eUSB drive.

“Detecting and Managing Faults” on page 25

“Locate an eUSB Drive” on page 104

“Determine if an eUSB Drive is Faulty” on page 104

“Remove the eUSB Drive” on page 105

“Install the eUSB Drive” on page 106

Remove a eUSB drive.

“Remove the eUSB Drive” on page 105

Install a eUSB drive.

“Install the eUSB Drive” on page 106

Related Information

■

“Identifying Components” on page 13

■

“Detecting and Managing Faults” on page 25

■

“Component Service Task Reference” on page 47

■

“Preparing for Service” on page 43

■

“Returning a Server to Operation” on page 235

Servicing the eUSB Drive

103

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Oracle Netra SPARC S7-2, Service Manual, Page: 103 / 258

Search results

Summary of Contents for Netra SPARC S7-2

Reviews: