Oracle Netra SPARC S7-2 Service Manual Download Page 97

Page: 97 / 258

Servicing NVMe Storage Drives

The procedure to install, remove, or replace an NVMe drive depends upon the OS. You can

replace the factory-installed NVMe and cables in case either of them become faulty. NVMe

support is provided on the motherboard.

Note -

NVMe storage drives are supported only on servers that are running Oracle Solaris.

Servers that are running Oracle VM, Windows Server, or VMware ESXi do not support NVMe

drives. Support for NVMe is on the motherboard.

Caution -

Overheating hazard

. There must be no empty drive slots. Use fillers.

Description

Links

Replace a faulty NVMe drive.

“Detecting and Managing Faults” on page 25

“Unmount an NVMe Drive” on page 98

“Remove an NVMe Drive” on page 99

“Verify Removal of an NVMe Drive” on page 100

“Install an NVMe Drive” on page 100

“Power On an NVMe Drive and Attach a Device

Driver” on page 101

“Verify the Operation of an NVMe Storage Drive” on page 102

Replace a faulty NVMe cable.

“Servicing the NVMe Cables” on page 207

Add an NVMe drive.

“Install an NVMe Drive” on page 100

“Power On an NVMe Drive and Attach a Device

Driver” on page 101

“Verify the Operation of an NVMe Storage Drive” on page 102

Remove an NVMe drive.

“Unmount an NVMe Drive” on page 98

“Remove an NVMe Drive” on page 99

“Verify Removal of an NVMe Drive” on page 100

Servicing NVMe Storage Drives

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Oracle Netra SPARC S7-2, Service Manual, Page: 97 / 258

Search results

Summary of Contents for Netra SPARC S7-2

Reviews: