Oracle Netra SPARC S7-2 Service Manual Download Page 220

Page: 220 / 258

Remove the LED Board and Cable

Lift the LED assembly from the server.

Remove the two screws securing the LED board to the LED assembly.

Lift the LED board from the LED assembly, and set it aside.

Consider your next step.

■

If replacing a faulty LED board, install a new LED board.

See

“Install the LED Board and Cable” on page 221

■

If you removed the LED board as part of another component's service

procedure, return to that procedure.

See

“Component Service Task Reference” on page 47

Related Information

■

“Determine if the LED Board Is Faulty” on page 217

■

“Install the LED Board and Cable” on page 221

■

“Preparing for Service” on page 43

■

“Returning a Server to Operation” on page 235

220

Netra SPARC S7-2 Server Service Manual • February 2017

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Oracle Netra SPARC S7-2, Service Manual, Page: 220 / 258

Search results

Summary of Contents for Netra SPARC S7-2

Reviews: